Hummer H1 (2006+). Manual — part 304
10-78 Body
______________________________________________________________________
Right Hood Retainer Bracket Replacement
Removal
Remove the four bolts, lockwashers, washers, right hood retainer bracket and the spacer from the hood (Figure 10-91).
Installation
Secure the right hood retainer bracket and the spacer to the hood with the four washers, lockwashers and the bolts (Figure 10-91).
Figure 10-91: Right Hood Retainer Bracket Replacement
Left Hood Retainer Bracket Replacement
Removal
Remove the four bolts, lockwashers, washers, left hood retainer bracket and the four washers from the hood (Figure 10-92).
Installation
Install the left hood retainer bracket on the hood with the eight washers, four lockwashers and the bolts (Figure 10-92).
Figure 10-92: Left Hood Retainer Bracket
ENGINE SPLASH SHIELD REPLACEMENT
Removal
WARNING: To avoid injury or damage to equipment, raise and support hood during removal and installation.
NOTE: This section covers the left engine splash shield, the right splash shield is part of the battery box and is detailed in section
twelve.
1.
Disconnect the fluid level sensor connector on the brake master cylinder.
2.
Remove the hood prop rod and the bracket (Refer to section 10).
3.
Remove the three locknuts, washers, bolts and the washer securing the splash shield to the support brackets and remove splash
shield.
SPACER
RIGHT HOOD
RETAINER BRACKET
HOOD
LEFT HOOD RETAINER BRACKET
_____________________________________________________________________
Body 10-79
Figure 10-93: Engine (Left) Splash Shield Assembly Replacement
Disassembly
1.
Remove the four locknuts, washers, bolts, upper seal and the retainer from the splash shield (Figure 10-93).
2.
Remove the two locknuts, washers, bolts and the lower seal from the splash shield (Figure 10-93).
Assembly
1.
Secure the upper seal and the retainer to the splash shield with the four locknuts, washers and the bolts.
2.
Secure the lower seal to the splash shield with the two locknuts, washers and the bolts.
Installation
1.
Secure the splash shield to the support bracket with the three locknuts, washers, bolts and the washer (Figure 10-93). Tighten
the bolts to 10 lb-ft (14 N•m).
2.
Install the hood prop rod and the bracket.
3.
Connect the fluid level sensor connector to the brake master cylinder.
RETAINER
SUPPORT
SPLASH SHIELD
AIRLIFT
BRACKET
BRACKET
UPPER
SEAL
LOWER
SEAL
HOOD PROP
ROD BRACKET
10-80 Body
______________________________________________________________________
WINDSHIELD ASSEMBLY
Windshield Glass and Weatherstrip Replacement
Removal
1.
Remove the windshield wiper arm and the blade.
2.
Remove the six bolts and the upper retainer from the windshield frame (Figure 10-94).
3.
Remove the four bolts and the center retainer from the windshield frame.
4.
Remove the four bolts and the lower retainer.
5.
Remove the weatherstrip and the glass from the windshield frame.
6.
Clean the sealing compound from the windshield frame.
Installation
1.
Apply a 1/8 in. (3 mm) bead of sealing compound to the edge of the glass and the windshield frame (Figure 10-94).
2.
Position the weatherstrip on the glass.
3.
Position the glass and the weatherstrip to the windshield frame with the center retainer and the four bolts.
4.
Secure the upper retainer to the windshield frame with the six bolts.
5.
Secure the lower retainer to the windshield frame with the four bolts
6.
Apply a thin bead of sealing compound to the top edge of the outside weatherstrip.
7.
Install the windshield wiper arm and the blade.
Figure 10-94: Windshield Glass Replacement
Windshield Assembly Replacement
WARNING: To avoid injury or damage to equipment, support windshield during removal and installation.
Removal
1.
Remove the soft top or loosen the roof assembly, as applicable.
2.
Remove the windshield wiper blade and the arm.
3.
Remove the windshield wiper linkage.
4.
Remove the windshield wiper arm pivots.
5.
Remove the two locknuts and the bolts securing the windshield assembly to the A-pillar (Figure 10-95).
CENTER
UPPER
WEATHERSTRIP
GLASS
WINDSHIELD
FRAME
RETAINER
RETAINER
LOWER RETAINER
_____________________________________________________________________
Body 10-81
Figure 10-95: Windshield Assembly Mounting
6.
Disconnect the roof harness, wiper motor, heated windshield, clearance light and the compass mirror connections at the center
pillar and pull the harness loose from the windshield center pillar (Figure 10-96).
7.
Remove the six bolts and the washers securing the windshield assembly to the two brackets (Figure 10-95).
8.
Remove the windshield assembly from the A-pillar.
9.
Remove the two seals from the windshield assembly.
10. Clean the remains of the seals from the windshield.
Figure 10-96: Wiring Harness Lead Location
A-PILLAR
WINDSHIELD
SEALS
BRACKET
ASSEMBLY
ROOF
HARNESS
CLEARANCE
LIGHT
HEATED
WINDSHIELD
COMPASS
MIRROR
WIPER
MOTOR
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст