Hummer H1 (2006+). Manual — part 305
10-82 Body
______________________________________________________________________
Disassembly
NOTE: Perform steps 1 and 2 for model 90. Perform step 3 for all other models.
1.
Remove the eleven rivets, former and the seal from the windshield assembly (Figure 10-97).
2.
Remove the eight rivets and the two corner caps from the windshield assembly and replace it if damaged.
3.
Remove the thirteen rivets, former and the seal from the windshield assembly (Figure 10-97).
4.
Clean the remains of the seal from the windshield assembly.
Assembly
NOTE: Perform steps 1 and 2 for model 90. Perform step 3 for all other models.
1.
Secure the seal and the former to the windshield assembly with the eleven rivets (Figure 10-97).
2.
Secure the two corner caps to the windshield assembly with the eight rivets.
3.
Secure the seal and the former to the windshield assembly and secure with the thirteen rivets (Figure 10-97).
Figure 10-97: Windshield Assembly Seal Replacement
Installation
1.
Position the two seals on the windshield assembly (Figure 10-95).
2.
Position the windshield assembly over the A-pillar.
FORMER
SEAL
CORNER CAP
WINDSHIELD
ASSEMBLY
_____________________________________________________________________
Body 10-83
3.
Secure the windshield assembly to the two brackets with the six bolts and the washers.
4.
Connect the two jumper harness leads to the body harness leads and insert the grommet into the windshield center pillar
(Figure 10-96).
5.
Secure the windshield assembly to the A-pillar with the two bolts and the locknuts (Figure 10-95).
6.
Install the windshield wiper arm pivots.
7.
Install the windshield wiper linkage.
8.
Install the windshield wiper arm and the blade.
9.
Install the soft top.
10-84 Body
______________________________________________________________________
HEATED WINDSHIELD
The optional heated windshield is capable of defrosting the windshield glass in less than 10 minutes at 0° F. The system is com-
prised of a rocker switch with an integrated time delay module (Figure 10-98), two relays and two fuses and in-glass heating ele-
ments.
Figure 10-98: Rocker Switch/Time Delay Module Location
Figure 10-99: Heating Element Junction Location
The rocker switch/time delay module is mounted on the power window master switch on the driver side of the front console (Fig-
ure 10-98).
Removal
1.
Remove the screws and pull the power window master switch from the radio bezel (Figure 10-98).
2.
Lift the connector clip and pull connector from the rocker switch/time delay module.
3.
Squeeze the clips on the rocker switch/time delay module and remove switch/module from the bezel.
Installation
1.
Push the rocker switch/time delay module into the bezel opening and snap it into bezel.
2.
Attach the electrical connector to the rocker switch/time delay module (Figure 10-99).
3.
Install the radio bezel.
TIME DELAY
MODULE
ROCKER
SWITCH
DRIVER
SIDE
WINDSHIELD
GLASS
PASSENGER SIDE
WINDSHIELD GLASS
FRONT
CONSOLE
HEATING
ELEMENT
JUNCTIONS
_____________________________________________________________________
Body 10-85
WINDSHIELD WIPER SYSTEM AND COMPONENTS
Windshield Wiper Motor Assembly Replacement
Removal
1.
Remove the windshield center trim from the windshield assembly.
2.
Remove the drivers compartment headliner.
3.
Disconnect the windshield wiper motor assembly harness from the crossbody harness (Figure 10-100).
4.
Remove the three bolts, washers and the lockwashers securing the windshield wiper motor assembly to the windshield
assembly.
5.
Remove the retainer securing the windshield wiper linkage to the windshield wiper motor cranking pin and remove the
windshield wiper motor assembly.
Installation
1.
Lubricate the windshield wiper motor cranking pin and secure the windshield wiper linkage to the windshield wiper motor
cranking pin with the retainer (Figure 10-100).
2.
Secure the windshield wiper motor assembly to the windshield assembly with the three lockwashers, washers and the bolts.
Tighten the bolts to 12 lb-ft (16 N•m).
3.
Connect the windshield wiper motor assembly harness to the crossbody harness.
4.
Install the drivers compartment headliner.
5.
Secure the windshield center trim to the windshield assembly.
Figure 10-100: Windshield Wiper Motor Assembly Replacement
Windshield Wiper Linkage Replacement
Removal
NOTE: Left and right side windshield wiper linkage replacement procedure is the same. This procedure covers the left side.
1.
Remove the windshield wiper motor assembly.
2.
Disconnect the windshield wiper linkage from the windshield wiper pivot cranking lever pin and remove the windshield wiper
linkage (Figure 10-101).
Installation
1.
Secure windshield wiper linkage to the windshield wiper pivot cranking lever pin (Figure 10-101).
WINDSHIELD
LINKAGE
WINDSHIELD WIPER
MOTOR ASSEMBLY
ASSEMBLY
WINDSHIELD WIPER
WINDSHIELD WIPER
MOTOR CRANKING PIN
WINDSHIELD WIPER MOTOR
ASSEMBLY HARNESS
RETAINER
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст