Toyota Tundra. Manual — part 1771
Fig. 112: Checking PCV Valve Operation
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
2
Blow air into the intake manifold side, and check that air passes through with difficulty
If the result is not as specified, replace the PCV valve sub-assembly
Fig. 113: Checking Air Passes
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
c
Remove the clean hose from the PCV valve
INSTALLATION
1
INSTALL PCV VALVE SUB-ASSEMBLY
a
Apply a light coat of engine oil to the O-ring, and install it to the valve
HINT:
When reusing the PCV valve, inspect the O-ring
If the O-ring has scratches or cuts, replace the PCV valve
2009 Toyota Tundra
2009 ENG NE Emission Control (3UR-FE) - Tundra
Fig. 114: Identifying O-Ring On PCV Valve
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
b
Install the PCV valve
Torque: 5.0 N*m (51 kgf*cm, 44 in.*lbf)
2
CONNECT PCV VALVE HOSE
Fig. 115: Identifying PCV Valve Hose
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
3
INSTALL NO. 2 ENGINE COVER (see INSTALLATION )
4
INSTALL INTAKE MANIFOLD
a
Install the intake manifold (see INSTALLATION )
2009 Toyota Tundra
2009 ENG NE Emission Control (3UR-FE) - Tundra
2009 ENGINE
Engine Mechanical (1GR-FE) - Tundra
ENGINE
ON-VEHICLE INSPECTION
1
INSPECT ENGINE COOLANT (See ON-VEHICLE INSPECTION )
2
INSPECT ENGINE OIL
3
INSPECT BATTERY (See ON-VEHICLE INSPECTION )
4
INSPECT AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY
5
INSPECT IGNITION TIMING
a
Warm up the engine
b
When using the Techstream:
1
Connect the Techstream to the DLC3
2
Enter the following menus:
Select: Powertrain/Engine and ECT/Data List/All Data/IGN Advance
3
Inspect the ignition timing during idling
Standard ignition timing: 8 to 12° BTDC @ idling (transmission in neutral position and
A/C switch OFF)
4
Check that the ignition timing advances immediately when the engine speed is increased
c
When not using Techstream:
1
Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3
SST 09843-18040
2
Remove the air cleaner cap
NOTE:
Turn all electrical systems OFF.
Perform the inspection when the cooling fan motor is turned OFF.
NOTE:
Be sure not to improperly connect the terminals. This may
damage the engine.
2009 Toyota Tundra
2009 ENGINE Engine Mechanical (1GR-FE) - Tundra
2009 Toyota Tundra
2009 ENGINE Engine Mechanical (1GR-FE) - Tundra
Fig. 1: Identifying DLC3 Connector Terminals
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
3
Pull out the wire harness as shown below
4
Connect the tester probe of a timing light to the wire of the ignition coil connector for the No
1 cylinder
5
Inspect the ignition timing during idling
Standard ignition timing: 8 to 12° BTDC @ idling (transmission in neutral position and
A/C switch OFF)
6
Remove SST from the DLC3
7
Inspect the ignition timing during idling
NOTE:
Use a timing light that detects primary signals.
After checking, be sure to wrap the wire harness with tape.
Fig. 2: Pulling Out Wire Harness
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
2009 Toyota Tundra
2009 ENGINE Engine Mechanical (1GR-FE) - Tundra
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст