Toyota Tundra. Manual — part 2373
Fig. 74: Identifying Steering Components With Torque Specifications (Tilt And Power Telescopic)
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
Fig. 75: Identifying Steering Column Components With Torque Specifications (Manual Tilt)
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
Fig. 76: Identifying Steering Column Components With Torque Specifications (Manual Tilt And
Telescopic)
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
2009 Toyota Tundra
2009 ENGINE Starting (3UR-FBE) - Tundra
Fig. 77: Identifying Steering Column Components With Torque Specifications (Power Tilt And Power
Telescopic)
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
Fig. 78: Identifying Ignition Switch And Related Components (Manual Tilt)
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
Fig. 79: Identifying Ignition Switch And Related Components (Manual Tilt And Telescopic)
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
2009 Toyota Tundra
2009 ENGINE Starting (3UR-FBE) - Tundra
Fig. 80: Identifying Ignition Switch And Related Components (Power Tilt And Power Telescopic)
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
REMOVAL
1
DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
2
REMOVE STEERING COLUMN ASSEMBLY
a
for Manual Tilt:
Remove the steering column assembly (See REMOVAL )
b
for Manual Tilt and Telescopic:
Remove the steering column assembly (See REMOVAL )
c
for Power Tilt and Power Telescopic:
Remove the steering column assembly (See REMOVAL )
3
REMOVE UPPER STEERING COLUMN WITH SWITCH BRACKET ASSEMBLY (for Manual
NOTE:
When disconnecting the cable, some systems need to be initialized
after the cable is reconnected (See INITIALIZATION ).
After the ignition switch is turned off, the navigation system requires
approximately 90 seconds to record various types of memory and
settings. As a result, after turning the ignition switch off, wait 90
seconds or more before disconnecting the cable from the negative (-)
battery terminal.
2009 Toyota Tundra
2009 ENGINE Starting (3UR-FBE) - Tundra
Tilt) (See DISASSEMBLY )
4
REMOVE UPPER STEERING COLUMN WITH SWITCH BRACKET ASSEMBLY (for Manual
Tilt and Manual Telescopic Steering Column) (See DISASSEMBLY )
5
REMOVE UPPER STEERING COLUMN WITH SWITCH BRACKET ASSEMBLY (for Power
Tilt and Power Telescopic Steering Column) (See DISASSEMBLY )
6
REMOVE IGNITION SWITCH ASSEMBLY (See INSPECTION )
INSPECTION
1
INSPECT IGNITION SWITCH ASSEMBLY
a
Measure the resistance according to the value(s) in the table below
Standard Resistance
RESISTANCE SPECIFIED CONDITION
Fig. 81: Identifying Ignition Switch Connector Terminals
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
If the result is not as specified, replace the ignition switch assembly
INSTALLATION
1
INSTALL IGNITION SWITCH ASSEMBLY (See REASSEMBLY )
2
INSTALL UPPER STEERING COLUMN WITH SWITCH BRACKET ASSEMBLY (for Manual
Tester Connection Switch Condition Specified Condition
All terminals
LOCK
10 kohms or higher
2 (ACC) - 4 (AM1)
ACC
Below 1 ohms
1 (IG1) - 4 (AM1)
ON
2 (ACC) - 4 (AM1)
5 (AM2) - 6 (IG2)
1 (IG1) - 4 (AM1)
START
3 (ST1) - 4 (AM1)
5 (AM2) 6 (IG2)
5 (AM2) - 7 (ST2)
2009 Toyota Tundra
2009 ENGINE Starting (3UR-FBE) - Tundra
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст