Toyota Tundra. Manual — part 2371
Fig. 61: Installing O-Ring To Guide
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
c
Install the dipstick guide with the bolt
Torque: 10 N*m (102 kgf*cm, 7 ft.*lbf)
d
Install the dipstick
7
INSTALL GENERATOR ASSEMBLY
a
Install the generator with the 2 bolts and 2 nuts
Torque: 43 N*m (439 kgf*cm, 32 ft.*lbf)
Fig. 62: Locating Generator Bolts And Nuts
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
b
Connect the generator connector
c
Connect the generator wire with the nut
Torque: 9.8 N*m (100 kgf*cm, 87 in.*lbf)
2009 Toyota Tundra
2009 ENGINE Starting (3UR-FBE) - Tundra
Fig. 63: Locating Generator Connector And Nut
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
d
Install the terminal cap
e
Install the harness bracket to the generator with the bolt
Torque: 31 N*m (316 kgf*cm, 23 ft.*lbf)
Fig. 64: Locating Wire Harness Bracket Bolt
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
8
CONNECT VANE PUMP ASSEMBLY
HINT:
Before performing the following procedures, move the spacer until the vane pump can be installed
2009 Toyota Tundra
2009 ENGINE Starting (3UR-FBE) - Tundra
Fig. 65: Moving Spacer
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
a
Connect the vane pump to the timing chain cover with the 2 bolts
Torque: 28 N*m (286 kgf*cm, 21 ft.*lbf)
Fig. 66: Locating Vane Pump Bolts
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
b
Connect the 2 clamps and power steering oil pressure switch connector
Fig. 67: Locating Clamps And Power Steering Oil Pressure Switch Connector
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
9
INSTALL FRONT FENDER APRON SEAL RH (See INSTALLATION )
10
INSTALL FAN AND GENERATOR V BELT (See INSTALLATION )
11
INSTALL AIR CLEANER ASSEMBLY (See INSTALLATION )
2009 Toyota Tundra
2009 ENGINE Starting (3UR-FBE) - Tundra
12
INSTALL AIR CLEANER HOSE ASSEMBLY (See INSTALLATION )
13
INSTALL V-BANK COVER SUB-ASSEMBLY (See INSTALLATION )
14
INSTALL NO. 1 ENGINE UNDER COVER (See REPLACEMENT )
15
CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
STARTER RELAY
ON-VEHICLE INSPECTION
1
DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
2
REMOVE STARTER RELAY (ST)
a
Remove the engine room relay box cover
b
Remove the starter relay from the engine room relay block
3
INSPECT STARTER RELAY
a
Measure the resistance according to the value(s) in the table below
Standard Resistance
RESISTANCE SPECIFIED CONDITION
NOTE:
When disconnecting the cable, some systems need to be initialized after
the cable is reconnected (See INITIALIZATION ).
NOTE:
When disconnecting the cable, some systems need to be initialized
after the cable is reconnected (See INITIALIZATION ).
After the ignition switch is turned off, the navigation system requires
approximately 90 seconds to record various types of memory and
settings. As a result, after turning the ignition switch off, wait 90
seconds or more before disconnecting the cable from the negative (-)
battery terminal.
Terminal
Connection
Condition
Specified
Condition
3 - 5
When battery voltage is not applied to terminals 1 and
2
10 kohms or higher
When battery voltage is applied to terminals 1 and 2
Below 1 ohms
2009 Toyota Tundra
2009 ENGINE Starting (3UR-FBE) - Tundra
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст