Toyota Tundra. Manual — part 2018
Fig. 212: Identifying Fuel Main And Return Hoses
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
b
Install the fuel pipe clamp
23
INSTALL RADIATOR ASSEMBLY (See INSTALLATION )
24
INSTALL FAN SHROUD (See INSTALLATION )
25
INSTALL FAN AND GENERATOR V BELT (See INSTALLATION )
26
INSTALL OIL COOLER ASSEMBLY (w/ Trailer Towing System)
a
Install the oil cooler (see INSTALLATION )
27
INSTALL RADIATOR SIDE DEFLECTOR LH (See INSTALLATION )
28
INSTALL RADIATOR SIDE DEFLECTOR RH (w/o Trailer Towing System) (See
INSTALLATION )
29
INSTALL OUTLET RADIATOR HOSE
30
INSTALL INLET RADIATOR HOSE
31
INSTALL AIR CLEANER ASSEMBLY
a
Install the air cleaner case with the 2 bolts
Torque: 5.0 N*m (51 kgf*cm, 44 in.*lbf)
Fig. 213: Locating Air Cleaner Case Bolts
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
b
Install the air cleaner element onto the air cleaner case
c
Install the air cleaner cap
2009 Toyota Tundra
2009 ENGINE Engine Mechanical (3UR-FE) - Tundra
1
Fasten the 4 hook clamps
Fig. 214: Locating Air Cleaner Assembly Hook Clamps
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
2
Connect the MAF meter connector
3
Attach the wire harness clamp
32
INSTALL AIR CLEANER HOSE ASSEMBLY
a
Install the air cleaner hose with the 2 clamps
Torque: 4.0 N*m (41 kgf*cm, 35 in.*lbf)
Fig. 215: Identifying Air Cleaner Hose Clamps
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
b
Connect the vacuum hose
c
Connect the ventilation hose
33
ADD ENGINE OIL (See REPLACEMENT )
34
ADD ENGINE COOLANT (See COOLANT )
35
CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
36
INSPECT FOR OIL LEAK
a
Inspect for engine oil leak (see REPLACEMENT )
NOTE:
Some systems need to be initialized after the cable is reconnected (see
INITIALIZATION ).
2009 Toyota Tundra
2009 ENGINE Engine Mechanical (3UR-FE) - Tundra
37
INSPECT FOR COOLANT LEAK (See COOLING SYSTEM )
38
INSPECT FOR EXHAUST GAS LEAK (See INSTALLATION )
39
INSPECT FOR FUEL LEAK (See INSTALLATION )
40
INSPECT SHIFT LEVER POSITION
a
for Column shift:
Refer to the following procedures (see ON-VEHICLE INSPECTION )
b
for Floor shift:
Refer to the following procedures (see ON-VEHICLE INSPECTION )
41
INSTALL V-BANK COVER SUB-ASSEMBLY
a
Attach the 2 V-bank cover hooks to the bracket Then align the 2 V-bank cover grommets with the
2 pins, and press down on the V-bank cover to attach the pins
Fig. 216: Installing V-Bank Cover Sub-Assembly
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
42
INSTALL COWL TOP OUTER PANEL SUB-ASSEMBLY (See INSTALLATION )
43
INSTALL WINDSHIELD WIPER MOTOR ASSEMBLY
a
Install the windshield wiper motor (see INSTALLATION )
44
INSTALL HOOD SUB-ASSEMBLY
a
Install the hood with the 4 bolts
Torque: 13 N*m (133 kgf*cm, 10 ft.*lbf)
2009 Toyota Tundra
2009 ENGINE Engine Mechanical (3UR-FE) - Tundra
Fig. 217: Installing Hood Sub-Assembly
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
b
Attach the lower part of the 2 hood supports to the hood support bolt ball joints
c
Attach the hood support clips
45
ADJUST HOOD SUB-ASSEMBLY (See ADJUSTMENT )
46
INSTALL NO. 1 ENGINE UNDER COVER (See REPLACEMENT )
47
INSPECT IGNITION TIMING (See ON-VEHICLE INSPECTION )
48
INSPECT ENGINE IDLE SPEED (See ON-VEHICLE INSPECTION )
49
INSPECT CO/HC (See ON-VEHICLE INSPECTION )
50
CHECK ENGINE OIL LEVEL (See LUBRICATION SYSTEM )
51
CHECK ENGINE COOLANT LEVEL (See COOLING SYSTEM )
ENGINE UNIT
COMPONENTS
Fig. 218: Identifying Engine Unit Components With Torque Specifications (1 Of 12)
NOTE:
Install the hood support while supporting the hood by hand.
NOTE:
Check that the hood support is engaged in the ball joint and that it
cannot be pulled out.
2009 Toyota Tundra
2009 ENGINE Engine Mechanical (3UR-FE) - Tundra
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст