Toyota Tundra. Manual — part 2362
Fig. 8: Exploded View Of Starter With Torque Specifications
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
REMOVAL
1
DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
2
REMOVE NO. 1 ENGINE UNDER COVER (See REPLACEMENT )
3
REMOVE V-BANK COVER SUB-ASSEMBLY (See REMOVAL )
4
REMOVE AIR CLEANER HOSE ASSEMBLY (See REMOVAL )
5
REMOVE AIR CLEANER ASSEMBLY (See REMOVAL )
6
REMOVE FAN AND GENERATOR V BELT (See REMOVAL )
7
REMOVE FRONT FENDER APRON SEAL RH (See REMOVAL )
8
DISCONNECT VANE PUMP ASSEMBLY
a
Disconnect the 2 clamps and power steering oil pressure switch connector
NOTE:
When disconnecting the cable, some systems need to be initialized
after the cable is reconnected (See INITIALIZATION ).
After the ignition switch is turned off, the navigation system requires
approximately 90 seconds to record various types of memory and
settings. As a result, after turning the ignition switch off, wait 90
seconds or more before disconnecting the cable from the negative (-)
battery terminal.
2009 Toyota Tundra
2009 ENGINE Starting (3UR-FBE) - Tundra
Fig. 9: Locating Clamps And Power Steering Oil Pressure Switch Connector
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
b
Remove the 2 bolts and disconnect the vane pump
Fig. 10: Locating Vane Pump Bolts
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
9
REMOVE GENERATOR ASSEMBLY
a
Disconnect the generator connector
b
Remove the terminal cap and nut, and disconnect the generator wire
Fig. 11: Locating Generator Connector And Nut
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
c
Remove the bolt and disconnect the wire harness bracket from the generator
2009 Toyota Tundra
2009 ENGINE Starting (3UR-FBE) - Tundra
Fig. 12: Locating Wire Harness Bracket Bolt
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
d
Remove the 2 bolts, 2 nuts and generator
Fig. 13: Locating Generator Bolts And Nuts
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
10
REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE
a
Remove the dipstick
b
Remove the bolt and dipstick guide
2009 Toyota Tundra
2009 ENGINE Starting (3UR-FBE) - Tundra
Fig. 14: Locating Dipstick Guide Bolt
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
c
Remove the O-ring from the dipstick guide
11
REMOVE FRONT EXHAUST PIPE ASSEMBLY
a
Disconnect the air fuel ratio sensor connector
b
Disconnect the heated oxygen sensor connector and 2 clamps
c
Remove the 2 bolts
d
Remove the 3 nuts and front exhaust pipe
e
Remove the 2 gaskets
12
REMOVE NO. 1 EXHAUST MANIFOLD HEAT INSULATOR (See REMOVAL )
13
REMOVE EXHAUST MANIFOLD SUB-ASSEMBLY RH (See REMOVAL )
14
REMOVE STARTER COVER
a
Remove the 3 bolts and starter cover
Fig. 15: Locating Starter Cover Bolts
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
15
REMOVE STARTER ASSEMBLY
a
Disconnect the starter connector
b
Remove the nut and disconnect the starter wire
Fig. 16: Locating Nut And Starter Wire
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
2009 Toyota Tundra
2009 ENGINE Starting (3UR-FBE) - Tundra
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст