Toyota Tundra. Manual — part 2360
Fig. 85: Identifying Ignition Switch Replacement Components With Torque Specifications (3 Of 10)
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
Fig. 86: Identifying Ignition Switch Replacement Components With Torque Specifications (4 Of 10)
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
Fig. 87: Identifying Ignition Switch Replacement Components With Torque Specifications (5 Of 10)
2009 Toyota Tundra
2009 ENG NE Starting (2UZ-FE) - Tundra
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
Fig. 88: Identifying Ignition Switch Replacement Components With Torque Specifications (6 Of 10)
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
Fig. 89: Identifying Ignition Switch Replacement Components With Torque Specifications (7 Of 10)
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
Fig. 90: Identifying Ignition Switch Replacement Components (8 Of 10)
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
2009 Toyota Tundra
2009 ENG NE Starting (2UZ-FE) - Tundra
Fig. 91: Identifying Ignition Switch Replacement Components (9 Of 10)
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
Fig. 92: Identifying Ignition Switch Replacement Components (10 Of 10)
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
REMOVAL
1
DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
2
REMOVE STEERING COLUMN ASSEMBLY
a
for Manual Tilt:
Remove the steering column (See REMOVAL )
b
for Manual Tilt and Telescopic:
Remove the steering column (see REMOVAL )
NOTE:
Some systems need to be initialized after the cable is reconnected
(see INITIALIZATION ).
After the ignition switch is turned OFF, the navigation system
requires approximately 90 seconds to record various types of
memory and settings. As a result, after turning the ignition switch
OFF, wait 90 seconds or more before disconnecting the cable from
the negative (-) battery terminal.
2009 Toyota Tundra
2009 ENG NE Starting (2UZ-FE) - Tundra
c
for Power Tilt and Power Telescopic:
Remove the steering column (see REMOVAL )
3
REMOVE UPPER STEERING COLUMN WITH SWITCH BRACKET ASSEMBLY (for Manual
Tilt) (See DISASSEMBLY )
4
REMOVE UPPER STEERING COLUMN WITH SWITCH BRACKET ASSEMBLY (for Manual
Tilt and Telescopic) (See DISASSEMBLY )
5
REMOVE UPPER STEERING COLUMN WITH SWITCH BRACKET ASSEMBLY (for Power
Tilt and Power Telescopic) (See DISASSEMBLY )
6
REMOVE IGNITION SWITCH ASSEMBLY (See DISASSEMBLY )
INSPECTION
1
INSPECT IGNITION SWITCH ASSEMBLY
a
Measure the resistance according to the value(s) in the table below
Standard resistance
IGNITION SWITCH ASSEMBLY
If the result is not as specified, replace the ignition switch assembly
Fig. 93: Identifying Ignition Switch Assembly Connector Terminal
Tester Connection Switch Condition Specified Condition
All terminals
LOCK
10 kohms or higher
2 (ACC) - 4 (AM1)
ACC
Below 1 ohms
1 (IG1) - 4 (AM1)
ON
2 (ACC) - 4 (AM1)
5 (AM2) - 6 (IG2)
1 (IG1) - 4 (AM1)
START
3 (ST1) - 4 (AM1)
5 (AM2) - 6 (IG2)
5 (AM2) - 7 (ST2)
2009 Toyota Tundra
2009 ENG NE Starting (2UZ-FE) - Tundra
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст