Toyota Tundra. Manual — part 615
Fig. 15: Identifying Front Power Seat Lumbar Switch Connector Terminals
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
NG: REPLACE FRONT POWER SEAT LUMBAR SWITCH (see REMOVAL )
OK: Go to next step
8. INSPECT FRONT SEAT ADJUSTER ASSEMBLY LH
a. Disconnect the Z2 switch connector.
b. Apply battery voltage and check the operation of the power seat.
OK
FRONT SEAT ADJUSTER ASSEMBLY LH
Measurement Condition
Specified Condition
Battery positive (+) --> Terminal Z2-4 (H)
Battery negative (-) --> Terminal Z2-1 (R)
Lumbar support moves forward (A)
Battery negative (-) --> Terminal Z2-4 (H)
Battery positive (+) --> Terminal Z2-1 (R)
Lumbar support moves rearward (B)
2009 Toyota Tundra
2009 ACCESSORIES AND EQUIPMENT Seat - Tundra
Fig. 16: Inspecting Front Seat Adjuster Assembly LH
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
NG: Go to step 9
OK: REPAIR OR REPLACE HARNESS OR CONNECTOR (FRONT POWER SEAT LUMBAR
SWITCH BATTERY AND BODY GROUND)
9. CHECK HARNESS AND CONNECTOR (FRONT POWER SEAT LUMBAR SWITCH
LUMBAR SUPPORT MOTOR LH)
a. Disconnect the Z2 switch connector.
b. Disconnect the Z7 motor connector.
c. Measure the resistance according to the value(s) in the table below.
Standard resistance
FRONT POWER SEAT LUMBAR SWITCH LUMBAR SUPPORT MOTOR LH
Tester Connection
Condition Specified Condition
Z2-1 (R) - Z7-2
Always
Below 1 ohms
22-4 (H) - Z7-1
Always
Z2-1 (R) - Body ground Always
10 kohms or higher
Z2-4 (H) - Body ground Always
2009 Toyota Tundra
2009 ACCESSORIES AND EQUIPMENT Seat - Tundra
Fig. 17: Identifying Front Power Seat Lumbar Switch And Lumbar Support Motor
Connector Terminals
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
NG: REPAIR OR REPLACE HARNESS OR CONNECTOR
OK: REPLACE FRONT SEAT ADJUSTER ASSEMBLY LH (see REMOVAL )
10. INSPECT FUSE (FR P/SEAT LH)
a. Remove the FR P/SEAT LH fuse from the main body ECU.
b. Measure the resistance according to the value(s) in the table below.
Standard resistance
FUSE (FR P/SEAT LH)
NG: REPLACE FUSE
OK: Go to next step
11. INSPECT LEG SUPPORT ADJUSTMENT SWITCH
Tester Connection Condition Specified Condition
FR P/SEAT LH fuse Always
Below 1 ohms
2009 Toyota Tundra
2009 ACCESSORIES AND EQUIPMENT Seat - Tundra
a. Remove the switch (see REMOVAL ).
b. Measure the resistance according to the value(s) in the table below.
Standard resistance
LEG SUPPORT ADJUSTMENT SWITCH
Fig. 18: Identifying Leg Support Adjustment Switch Connector Terminals
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
NG: REPLACE LEG SUPPORT ADJUSTMENT SWITCH (see REMOVAL )
OK: Go to next step
12. INSPECT FRONT SEAT ADJUSTER ASSEMBLY LH
Tester Connection Switch Condition Specified Condition
1 (CSNF) - 3 (B)
OPEN
Below 1 ohms
4 (CSNR) - 5 (E2)
1 (CSNF) - 2 (E1)
OFF
4 (CSNR) - 5 (E2)
1 (CSNF) - 2 (E1)
CLOSE
3 (B) - 4 (CSNR)
2009 Toyota Tundra
2009 ACCESSORIES AND EQUIPMENT Seat - Tundra
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст