Toyota Tundra. Manual — part 701
Fig. 5: Identifying Main Body ECU Connector Terminals
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
a. Disconnect the DA, DB, DD and J4 ECU connectors.
b. Measure the voltage and resistance according to the value(s) in the table below.
MAIN BODY ECU TERMINALS VOLTAGE CHART
Terminal No.
Wiring Color
Terminal Description
Condition
Specified
2009 Toyota Tundra
2009 ACCESSORIES AND EQUIPMENT Theft Deterrent - Tundra
If the result is not as specified, there may be a malfunction on the wire harness side.
c. Reconnect the ECU connectors.
d. Measure the voltage according to the value(s) in the table below.
MAIN BODY ECU TERMINALS VOLTAGE CHART
(Symbols)
Condition
DA-1 (ACC) - Body
ground
B - Body
ground
ACC power supply
Always
11 to 14 V
DA-1 (IG) - Body
ground
B - Body
ground
IG power supply
Always
11 to 14 V
DA-1 (ALTB) - Body
ground
B - Body
ground
+B power supply
Always
11 to 14 V
DB-13 (BECU) -
Body ground
GR - Body
ground
BECU power supply
Always
11 to 14 V
DD-62 (GND1) -
Body ground
W-B - Body
ground
Body ground
Always
Below 1 ohms
DD-62 (GND2) -
Body ground
W-B - Body
ground
Body ground
Always
Below 1 ohms
J4-16 (HCTY) - Body
ground
V - Body
ground
Engine hood courtesy
switch signal
Engine hood
closed
10 kohms or
higher
Engine hood
open
Below 1 ohms
Terminal No.
(Symbols)
Wiring
Color
Terminal
Description
Condition
Specified
Condition
J1-4 (IND) -
Body ground
P - Body
ground
Security indicator
signal
Security indicator illuminates
(illuminates only for 60 sec. in
alarm sounding state (it is blinking
when system is in armed state))
3 to 5V
J1-6 (SH) -
Body ground
W - Body
ground
Security horn signal
Armed state
Below 1 V
Security horn is sounding (theft
deterrent system is in alarm
sounding state)
Pulse
generation
J2-4 (HAZ) -
Body ground
O - Body
ground
Hazard warning
light signal
Armed state
Below 1 V
System is in alarm sounding state
Pulse
generation
J4-17 (GBS)* -
Body ground
L - Body
ground
Glass breakage
sensor ECU signal
Armed state
Below 1 V
Glass breakage sensor ECU signal
system is in alarm sounding state
Pulse
generation
DB-1 (HORN)
- Body ground
V - Body
ground
Horn signal (low
pitched and high
pitched)
Armed state
Below 1 V
Horn is sounding
11 to 14 V
HINT:
2009 Toyota Tundra
2009 ACCESSORIES AND EQUIPMENT Theft Deterrent - Tundra
If the result is not as specified, there may be a malfunction on the wire harness side, or the glass
breakage sensor ECU may have a malfunction.
DTC CHECK / CLEAR
1. CHECK DTC
a. Connect Techstream to the DLC3.
b. Turn the ignition switch ON.
c. Turn the tester on.
d. Enter the following menus:
Techstream - Select: Body / Main Body / Trouble Codes.
e. Read the DTCs.
2. CLEAR DTC
a. Connect Techstream to the DLC3.
b. Turn the ignition switch ON.
c. Turn the tester on.
d. Enter the following menus:
Techstream - Select: Body / Main Body / Trouble Codes.
e. Erase the DTCs.
DATA LIST / ACTIVE TEST
1. DATA LIST
HINT:
Using Techstream to read the Data List allows the values or states of switches, sensors, actuators and
other items to be read without removing any parts. This non-intrusive inspection can be very useful
because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading
the Data List information early in troubleshooting is one way to save diagnostic time.
a. Connect Techstream to the DLC3.
b. Turn the ignition switch ON.
c. Turn the tester on.
*: w/ Glass Breakage Sensor
NOTE:
In the table below, the values listed under "Normal Condition" are
reference values. Do not depend solely on these reference values when
deciding whether a part is faulty or not.
2009 Toyota Tundra
2009 ACCESSORIES AND EQUIPMENT Theft Deterrent - Tundra
d. Enter the following menus:
Techstream - Select: Body / Main Body / Data List.
e. According to the display on the tester, read the "Data List".
Techstream
Main Body
TECHSTREAM MAIN BODY CHART
2. ACTIVE TEST
HINT:
Using Techstream to perform Active Tests allows relays, VSVs, actuators and other items to be operated
without removing any parts. This non-intrusive functional inspection can be very useful because
intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests
early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while
performing Active Tests.
a. Connect Techstream to the DLC3.
b. Turn the ignition switch ON.
c. Turn the tester on.
d. Enter the following menus:
Techstream - Select: Body / (desired system) / Active Test.
e. According to the display on the tester, perform the "Active Test".
Tester Display
Measurement Item/Range
Normal Condition
Diagnostic
Note
Hood Courtesy
Switch
Engine hood courtesy switch /
ON or OFF
ON: Engine hood is
open
OFF: Engine hood is
closed
-
IG SW
Ignition switch / ON or OFF
ON: Ignition switch
ON
OFF: Ignition switch
OFF
-
Glass Break Sensor
Detection*
Glass breakage sensor
detection / ON or OFF
ON: Glass breakage
sensor ON
OFF: Glass breakage
sensor OFF
-
HINT:
*: w/ Glass Breakage Sensor
2009 Toyota Tundra
2009 ACCESSORIES AND EQUIPMENT Theft Deterrent - Tundra
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст