Toyota Tundra. Manual — part 213
Standard resistance
TESTER CONNECTION SPECIFIED CONDITION
NG: REPLACE FRONT NO. 1 SPEAKER (see REMOVAL )
Fig. 216: Identifying Front No. 1 Speaker Connector Terminals
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
OK: Go to next step.
6. CHECK HARNESS AND CONNECTOR (FRONT NO. 2 SPEAKER - FRONT NO. 1 SPEAKER)
a. Disconnect the M8, N10, K11 and K13 speaker connectors.
b. Measure the resistance according to the value(s) in the table below.
Standard resistance:
for LH
TESTER CONNECTION SPECIFIED CONDITION
for RH
TESTER CONNECTION SPECIFIED CONDITION
Tester Connection Condition Specified Condition
1 - 2
Always
3.2 to 4.8 ohms
Tester Connection
Condition Specified Condition
K13-1 (+) - N10-1
Always
Below 1 ohms
K13-2 (-) - N10-2
K13-1 (+) - Body ground
Always
10 kohms or higher
K13-2 (-) - Body ground
Tester Connection
Condition Specified Condition
K11-1 (+) - M8-1
Always
Below 1 ohms
K11-2 (-) - M8-2
K11-1 (+) - Body ground
2009 Toyota Tundra
2009 ACCESSORIES AND EQUIPMENT Audio/Visual - Tundra
NG: REPAIR OR REPLACE HARNESS OR CONNECTOR
Fig. 217: Identifying M8, N10, K11 And K13 Speaker Connector Terminals
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
OK: REPLACE FRONT NO. 2 SPEAKER (see REMOVAL )
7. INSPECT REAR NO. 1 SPEAKER
a. Disconnect the O1 and O7 speaker connectors.
b. Measure the resistance according to the value(s) in the table below.
Standard resistance
TESTER CONNECTION SPECIFIED CONDITION
NG: REPLACE REAR NO. 1 SPEAKER (see REMOVAL )
K11-2 (-) - Body ground
Always
10 kohms or higher
Tester Connection Condition Specified Condition
1 - 2
Always
3.2 to 4.8 ohms
2009 Toyota Tundra
2009 ACCESSORIES AND EQUIPMENT Audio/Visual - Tundra
Fig. 218: Identifying Rear No. 1 Speaker Connector Terminals
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
OK: Go to next step.
8. CHECK HARNESS AND CONNECTOR (RADIO RECEIVER - REAR NO. 1 SPEAKER)
a. Disconnect the K2 receiver connector.
b. Disconnect the O1 and O7 speaker connectors.
c. Measure the resistance according to the value(s) in the table below.
Standard resistance:
for LH
TESTER CONNECTION SPECIFIED CONDITION
for RH
TESTER CONNECTION SPECIFIED CONDITION
Tester Connection
Condition Specified Condition
K2-2 (RL+) - O7-1
Always
Below 1 ohms
K2-6 (RL-) - O7-2
K2-2 (RL+) - Body ground
Always
10 kohms or higher
K2-6 (RL-) - Body ground
Tester Connection
Condition Specified Condition
K2-1 (RR+) - O1-1
Always
Below 1 ohms
K2-3 (RR-) - O1-2
K2-1 (RR+) - Body ground
Always
10 kohms or higher
K2-3 (RR-) - Body ground
2009 Toyota Tundra
2009 ACCESSORIES AND EQUIPMENT Audio/Visual - Tundra
Fig. 219: Checking Harness And Connector (Radio Receiver - Rear No. 1 Speaker)
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
Result:
RESULT REFERENCE
B: REPLACE RADIO RECEIVER (see REMOVAL )
C: REPLACE RADIO RECEIVER (see REMOVAL )
A: REPAIR OR REPLACE HARNESS OR CONNECTOR
SOUND SIGNAL CIRCUIT BETWEEN RADIO RECEIVER AND STEREO COMPONENT
AMPLIFIER
DESCRIPTION
The radio receiver sends a sound signal to the stereo component amplifier through this circuit.
The sound signal that has been sent is amplified by the stereo component amplifier, and then is sent to the
speakers.
Result
Proceed to
NG
A
OK (for Column Shift Type)
B
OK (for Floor Shift Type)
C
2009 Toyota Tundra
2009 ACCESSORIES AND EQUIPMENT Audio/Visual - Tundra
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст