Toyota Tundra. Manual — part 901
OK: The Techstream displays as shown in the table according to the operation of each switch.
NG: Go to step 3
OK: REPLACE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY (SLIDING ROOF ECU) (see
DISASSEMBLY )
3. INSPECT SLIDING ROOF SWITCH
a. Remove the sliding roof switch (see REMOVAL ).
b. Measure the resistance according to the value(s) in the table below.
Standard resistance
SLIDING ROOF SWITCH RESISTANCE SPECIFICATION
to up
Down
Switch
Sliding roof down switch signal/
ON or OFF
ON: TILT switch is pressed to
down
OFF: TILT switch is not pressed
to down
-
Tester Connection
Switch Condition
Specified Condition
1(UP) - 5(E)
TILT switch is pressed to up
Below 1 ohms
1 (UP) - 5 (E)
TILT switch is not pressed to up
10 kohms or higher
2 (DWN) - 5 (E) TILT switch is pressed to down
Below 1 ohms
2 (DWN) - 5 (E) TILT switch is not pressed to down
10 kohms or higher
4 (OPN) - 5 (E)
SLIDE switch is pressed to open
Below 1 ohms
4(OPN) - 5(E)
SLIDE switch is not pressed to open 10 kohms or higher
3(CLS) - 5(E)
SLIDE switch is pressed to close
Below 1 ohms
3(CLS) - 5(E)
SLIDE switch is not pressed to close 10 kohms or higher
2009 Toyota Tundra
2009 ACCESSORIES AND EQUIPMENT Sliding Roof - Tundra
Fig. 15: Identifying Sliding Roof Switch Connector Terminals
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
NG: REPLACE SLIDING ROOF SWITCH (see REMOVAL )
OK: Go to Next Step
4. INSPECT ROOF CONSOLE BOX ASSEMBLY
a. Remove the roof console box with sliding roof switch (see REMOVAL ).
b. Measure the resistance according to the value(s) in the table below.
Standard resistance
ROOF CONSOLE BOX ASSEMBLY RESISTANCE SPECIFICATION
Tester Connection
Switch Condition
Specified Condition
6(UP) - 7 (E)
TILT switch is pressed to up
Below 1 ohms
6 (UP) - 7 (E)
TILT switch is not pressed to up
10 kohms or higher
5 (DWN) - 7 (E) TILT switch is pressed to down
Below 1 ohms
5 (DWN) - 7 (E) TILT switch is not pressed to down
10 kohms or higher
4 (OPN) - 7 (E)
SLIDE switch is pressed to open
Below 1 ohms
4 (OPN) - 7 (E)
SLIDE switch is not pressed to open 10 kohms or higher
3 (CLS) - 7 (E)
SLIDE switch is pressed to close
Below 1 ohms
3 (CLS) - 7 (E)
SLIDE switch is not pressed to close 10 kohms or higher
2009 Toyota Tundra
2009 ACCESSORIES AND EQUIPMENT Sliding Roof - Tundra
Fig. 16: Identifying Roof Console Box Assembly Connector Terminals
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
NG: REPLACE ROOF CONSOLE BOX ASSEMBLY (See REMOVAL )
OK: Go to Next Step
5. CHECK HARNESS AND CONNECTOR (SLIDING ROOF ECU - ROOF CONSOLE BOX)
a. Disconnect the W3 ECU connector.
b. Disconnect the W7 switch connector.
c. Measure the resistance according to the value(s) in the table below.
Standard resistance
HARNESS AND CONNECTOR (SLIDING ROOF ECU - ROOF CONSOLE BOX)
RESISTANCE SPECIFICATION
Tester Connection
Condition Specified Condition
W3-1 (UP) - W7-6 (UP)
Always
Below 1 ohms
W3-2(DWN) - W7-5 (DWN) Always
Below 1 ohms
W3-6 (OPN) - W7-4 (OPN)
Always
Below 1 ohms
W3-7 (CLS) - W7-3 (CLS)
Always
Below 1 ohms
W7-6 (UP) - Body ground
Always
10 kohms or higher
W7-5 (DWN) - Body ground Always
10 kohms or higher
W7-3 (CLS) - Body ground
Always
10 kohms or higher
W7-4 (OPN) - Body ground
Always
10 kohms or higher
W7-7 (E) - Body ground
Always
Below 1 ohms
2009 Toyota Tundra
2009 ACCESSORIES AND EQUIPMENT Sliding Roof - Tundra
Fig. 17: Identifying W3 ECU Connector And W7 Roof Console Box Connector
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
NG: REPAIR OR REPLACE HARNESS OR CONNECTOR
OK: REPLACE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY (SLIDING ROOF ECU) (see
DISASSEMBLY )
SLIDING ROOF ECU POWER SOURCE CIRCUIT
DESCRIPTION
If the sliding function and tilt function do not operate, there may be a malfunction in the sliding roof ECU
power source circuit.
WIRING DIAGRAM
2009 Toyota Tundra
2009 ACCESSORIES AND EQUIPMENT Sliding Roof - Tundra
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст