Toyota Tundra. Manual — part 321
2. REMOVE LOWER NO. 2 STEERING WHEEL COVER (See REMOVAL )
3. REMOVE LOWER NO. 3 STEERING WHEEL COVER (See REMOVAL )
4. REMOVE STEERING PAD (w/o Steering Pad Switch) (See REMOVAL )
5. REMOVE STEERING PAD (w/ Steering Pad Switch) (See REMOVAL )
6. REMOVE CRUISE CONTROL MAIN SWITCH
a. Disconnect the connector.
b. Remove the 2 screws.
Fig. 25: Locating Cruise Control Main Switch Connector
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
c. Remove the switch, as shown in the illustration.
Fig. 26: Identifying Switch
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
NOTE:
Some systems need to be initialized after the cable is reconnected (see
INITIALIZATION ).
NOTE:
After the ignition switch is turned OFF, the navigation system requires
approximately 90 seconds to record various types of memory and
settings. As a result, after turning the ignition switch OFF, wait 90 seconds
or more before disconnecting the cable from the negative (-) battery
terminal.
2009 Toyota Tundra
2009 ACCESSORIES AND EQUIPMENT Cruise Control - Tundra
INSPECTION
1. INSPECT CRUISE CONTROL MAIN SWITCH
a. Measure the resistance according to the value(s) in the table below.
Fig. 27: Inspecting Cruise Control Main Switch
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
Standard resistance
CRUISE CONTROL MAIN SWITCH
If the result is not as specified, replace the cruise control main switch.
INSTALLATION
1. INSTALL CRUISE CONTROL MAIN SWITCH
a. Install the switch, as shown in the illustration.
Tester Connection
Switch Condition
Specified Condition
1 (ECC) - 3 (CCS)
Neutral
10 kohms or higher
+RES
235 to 245 ohms
-SET
620 to 640 ohms
CANCEL
1510 to 1570 ohms
Main Switch OFF
10 kohms or higher
Main Switch ON
Below 1 ohms
2009 Toyota Tundra
2009 ACCESSORIES AND EQUIPMENT Cruise Control - Tundra
Fig. 28: Identifying Switch
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
b. Install the 2 screws.
c. Connect the connector.
Fig. 29: Locating Connector Screws
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
2. INSTALL STEERING PAD (w/ Steering Pad Switch) (See INSTALLATION )
3. INSTALL STEERING PAD (w/o Steering Pad Switch) (See INSTALLATION )
4. INSTALL LOWER NO. 3 STEERING WHEEL COVER (See INSTALLATION )
5. INSTALL LOWER NO. 2 STEERING WHEEL COVER (See INSTALLATION )
6. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
7. CHECK SRS WARNING LIGHT
a. Check the SRS warning light (see DIAGNOSIS SYSTEM ).
NOTE:
Some systems need to be initialized after the cable is reconnected (see
INITIALIZATION ).
2009 Toyota Tundra
2009 ACCESSORIES AND EQUIPMENT Cruise Control - Tundra
2009 ACCESSORIES AND EQUIPMENT
Door Lock - Tundra
POWER DOOR LOCK CONTROL SYSTEM
PARTS LOCATION
Fig. 1: Identifying Location Of Power Door Lock Control System Components (1 Of 2)
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
2009 Toyota Tundra
2009 ACCESSORIES AND EQUIPMENT Door Lock - Tundra
2009 Toyota Tundra
2009 ACCESSORIES AND EQUIPMENT Door Lock - Tundra
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст