Toyota Tundra. Manual — part 2370
d
Using a T30 "TORX" socket wrench, install the starter drive housing with the 2 bolts
Torque: 6.0 N*m (61 kgf*cm, 53 in.*lbf)
Fig. 54: Locating Starter Drive Housing Bolts
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
7
INSTALL MAGNET STARTER SWITCH ASSEMBLY
a
Temporarily install the magnet switch by hooking its tip to the upper side of the pinion drive lever
b
Install the 2 nuts
Torque: 7.5 N*m (76 kgf*cm, 66 in.*lbf)
Fig. 55: Locating Magnet Starter Switch Assembly Nuts
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
c
Connect the lead wire to the terminal with the nut
Torque: 6.5 N*m (66 kgf*cm, 57 in.*lbf)
2009 Toyota Tundra
2009 ENGINE Starting (3UR-FBE) - Tundra
Fig. 56: Locating Lead Wire Nut
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
INSTALLATION
1
INSTALL STARTER ASSEMBLY
a
Install the flywheel housing side cover
Fig. 57: Locating Flywheel Housing Side Cover
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
b
Install the starter with the 2 bolts
Torque: 37 N*m (377 kgf*cm, 27 ft.*lbf)
2009 Toyota Tundra
2009 ENGINE Starting (3UR-FBE) - Tundra
Fig. 58: Locating Starter Mounting Bolts
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
c
Install the starter wire with the nut
Torque: 9.8 N*m (100 kgf*cm, 87 in.*lbf)
Fig. 59: Locating Nut And Starter Wire
2009 Toyota Tundra
2009 ENGINE Starting (3UR-FBE) - Tundra
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
d
Connect the starter connector
2
INSTALL STARTER COVER
a
Install the starter cover with the 3 bolts
Torque: 12 N*m (122 kgf*cm, 9 ft.*lbf)
Fig. 60: Locating Starter Cover Bolts
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
3
INSTALL EXHAUST MANIFOLD SUB-ASSEMBLY RH (See INSTALLATION )
4
INSTALL NO. 1 EXHAUST MANIFOLD HEAT INSULATOR (See INSTALLATION )
5
INSTALL FRONT EXHAUST PIPE ASSEMBLY
a
Install a new gasket and the exhaust pipe to the exhaust manifold RH with 3 new nuts
Torque: 54 N*m (554 kgf*cm, 40 ft.*lbf)
b
Install a new gasket and the exhaust pipe to the center exhaust pipe with the 2 bolts
Torque: 48 N*m (489 kgf*cm, 35 ft.*lbf)
c
Connect the air fuel ratio sensor connector
d
Connect the heated oxygen sensor connector and 2 clamps
6
INSTALL ENGINE OIL LEVEL DIPSTICK GUIDE
a
Apply a light coat of engine oil to a new O-ring
b
Install the O-ring to the guide
2009 Toyota Tundra
2009 ENGINE Starting (3UR-FBE) - Tundra
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст