Toyota Tundra. Manual — part 429
w/o TAIL Cancel Switch
RESISTANCE W/O TAIL CANCEL SWITCH REFERENCE
w/ TAIL Cancel Switch
RESISTANCE W/ TAIL CANCEL SWITCH REFERENCE
NG: REPAIR OR REPLACE HARNESS OR CONNECTOR
OK: REPLACE COMBINATION METER ASSEMBLY (see REMOVAL )
ACCESSORY METER DOES NOT ILLUMINATE
DESCRIPTION
This circuit provides power to the accessory meter.
The cruise information display of the accessory meter shows the vehicle information input into the
combination meter. The display can be changed by using the drive monitor switch.
WIRING DIAGRAM
Tester Connection
Condition Specified Condition
J28-1 (RHIG) - L4-7 (T)
Always
Below 1 ohms
J28-2 (TR) - L4-3 (RV)
J28-3 (E2) - L4-1 (E)
Tester Connection
Condition Specified Condition
J28-1 (RHIG) - L4-7 (T)
Always
Below 1 ohms
J28-2 (TR) - L4-3 (RV)
J28-3 (E2) - L4-1 (E)
J28-38 (TC) - L4-5 (TC)
2009 Toyota Tundra
2009 ACCESSORIES AND EQUIPMENT Meter - Tundra
Fig. 47: Accessory Meter Does Not Illuminate - Wiring Diagram (1 Of 2)
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
2009 Toyota Tundra
2009 ACCESSORIES AND EQUIPMENT Meter - Tundra
Fig. 48: Accessory Meter Does Not Illuminate - Wiring Diagram (2 Of 2)
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
INSPECTION PROCEDURE
1. CHECK ACCESSORY METER ASSEMBLY
a. Check the malfunction of the accessory meter.
Result
ACCESSORY METER ASSEMBLY RESULT REFERENCE
B: Go to step 6
A: Go to next step
2. INSPECT FUSE (DOME, ECU-IG NO. 1, ACC)
a. Remove the DOME fuse from the engine room junction block.
b. Remove the ECU-IG No. 1 and ACC fuses from the main body ECU.
c. Measure the resistance according to the value(s) in the table below.
Result
Proceed to
Accessory meter does not display at all
A
Cruise information display does not change (w/ Cruise Information)
B
2009 Toyota Tundra
2009 ACCESSORIES AND EQUIPMENT Meter - Tundra
Standard resistance
FUSE (DOME, ECU-IG NO. 1, ACC) RESISTANCE REFERENCE
NG: REPLACE FUSE
OK: Go to next step
3. CHECK HARNESS AND CONNECTOR (ACCESSORY METER - BATTERY AND BODY
GROUND)
a. Disconnect the K20 accessory meter connector.
Fig. 49: Identifying K20 Accessory Meter Connector Terminal
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
b. Measure the voltage according to the value(s) in the table below.
Standard voltage
HARNESS AND CONNECTOR (ACCESSORY METER - BATTERY AND BODY
GROUND) VOLTAGE SPECIFICATIONS
c. w/o Cruise information
1. Measure the resistance according to the value(s) in the table below.
Standard resistance
Tester Connection Condition Specified Condition
DOME fuse
Always
Below 1 ohms
ECU-IG No. 1 fuse
ACC fuse
Tester Connection
Switch Condition Specified Condition
K20-24 (B) - Body ground
Always
11 to 14 V
K20-23 (IG) - Body ground
Ignition switch ON
11 to 14 V
K20-22 (ACC) - Body ground Ignition switch ACC
11 to 14 V
2009 Toyota Tundra
2009 ACCESSORIES AND EQUIPMENT Meter - Tundra
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст