Toyota Tundra. Manual — part 2482
b. Measure the voltage according to the value(s) in the table below.
Standard voltage
FOG LIGHT RELAY - BATTERY
NG: REPAIR OR REPLACE HARNESS OR CONNECTOR
OK: Go to next step
6. CHECK HARNESS AND CONNECTOR (FR FOG RELAY - FRONT FOG LIGHT BULB)
Fig. 37: Identifying FR Fog Relay And Front Fog Light Connector Terminals
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
a. Remove the fog light relay from the engine room relay block.
b. for LH:
1. Disconnect the A30 front fog light connector.
2. Measure the resistance according to the value(s) in the table below.
Standard resistance
FR FOG RELAY - FRONT FOG LIGHT BULB LH
c. for RH:
1. Disconnect the A31 front fog light connector.
Tester Connection
Switch Condition
Specified Condition
Fog light relay terminal 1 - Body ground Light control switch TAIL
11 to 14 V
Fog light relay terminal 3 - Body ground
Always
Tester Connection
Condition Specified Condition
Fog light relay terminal 5 - A30-2
Always
Below 1 ohms
Fog light relay terminal 5 - Body ground Always
10 kohms or higher
2009 Toyota Tundra
2009 ACCESSORIES AND EQUIPMENT Lighting - Tundra
2. Measure the resistance according to the value(s) in the table below.
Standard resistance
FR FOG RELAY - FRONT FOG LIGHT BULB RH
NG: REPAIR OR REPLACE HARNESS OR CONNECTOR
OK: Go to next step
7. CHECK FRONT FOG LIGHT
a. Disconnect the J4 ECU connector.
Fig. 38: Identifying Main Body ECU Connector Terminals
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
b. Using a service wire, connect J4-4 (FFGO) on the wire harness side and body ground.
c. Check that the front fog light illuminates.
OK: Front fog light illuminates.
NG: REPAIR OR REPLACE HARNESS OR CONNECTOR (FOG LIGHT RELAY - MAIN
BODY ECU)
OK: REPLACE MAIN BODY ECU
TURN SIGNAL LIGHT CIRCUIT
Tester Connection
Condition Specified Condition
Fog light relay terminal 5 - A31-2
Always
Below 1 ohms
Fog light relay terminal 5 - Body ground Always
10 kohms or higher
2009 Toyota Tundra
2009 ACCESSORIES AND EQUIPMENT Lighting - Tundra
DESCRIPTION
The turn signal flasher receives a turn signal switch signal from the headlight dimmer switch, and illuminates
the front turn signal light, outer rear view mirror and rear combination light.
WIRING DIAGRAM
Fig. 39: Identifying Turn Signal Light - Wiring Diagram
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
2009 Toyota Tundra
2009 ACCESSORIES AND EQUIPMENT Lighting - Tundra
INSPECTION PROCEDURE
1. CHECK TURN SIGNAL LIGHT
a. Check that the turn signal lights blink.
Result
TURN SIGNAL LIGHT
B: Go to step 4
C: Go to step 5
D: Go to step 6
A: Go to next step
2. INSPECT FUSE (LH-IG, TURN-HAZ)
a. Remove the LH-IG fuse from the main body ECU.
b. Remove the TURN-HAZ fuse from the engine room junction block.
c. Measure the resistance according to the value(s) in the table below.
Standard resistance
LH-IG, TURN-HAZ
NG: REPLACE FUSE
OK: Go to next step
3. CHECK HARNESS AND CONNECTOR (TURN SIGNAL FLASHER - BATTERY AND BODY
GROUND)
a. Disconnect the J29 relay connector.
Result
Proceed to
All turn signal lights do not blink
A
Only front turn signal light does not blink
B
Only rear combination light does not blink
C
Only door mirror foot light does not blink
D
Tester Connection Condition Specified Condition
LH-IG fuse
Always
Below 1 ohms
TURN-HAZ fuse
2009 Toyota Tundra
2009 ACCESSORIES AND EQUIPMENT Lighting - Tundra
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст