Toyota Tundra. Manual — part 2483
Fig. 40: Identifying Turn Signal Flasher Connector Terminals
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
b. Measure the voltage according to the value(s) in the table below.
Standard voltage
TURN SIGNAL FLASHER - BATTERY AND BODY GROUND VOLTAGE
c. Measure the resistance according to the value(s) in the table below.
Standard resistance
TURN SIGNAL FLASHER - BATTERY AND BODY GROUND RESISTANCE
NG: REPAIR OR REPLACE HARNESS OR CONNECTOR
OK: PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS
TABLE
4. CHECK HARNESS AND CONNECTOR (FRONT TURN SIGNAL LIGHT - TURN SIGNAL
FLASHER AND BODY GROUND)
a. for LH:
1. Disconnect the A12 light connector.
Tester Connection
Switch Condition Specified Condition
J29-3 (IG) - Body ground
Ignition switch ON
11 to 14 V
Ignition switch OFF
Below 1 V
J29-1 (B) - Body ground
Always
11 to 14 V
Tester Connection
Condition Specified Condition
J29-4 (E) - Body ground Always
Below 1 ohms
2009 Toyota Tundra
2009 ACCESSORIES AND EQUIPMENT Lighting - Tundra
2. Disconnect the J29 relay connector.
Fig. 41: Identifying Front LH Turn Signal Light Connector Terminals
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
3. Measure the resistance according to the value(s) in the table below.
Standard resistance
FRONT TURN SIGNAL LIGHT - TURN SIGNAL FLASHER AND BODY GROUND
LH
b. for RH:
1. Disconnect the A13 light connector.
2. Disconnect the J29 relay connector.
Tester Connection
Condition Specified Condition
A12-3 (B) - J29-10 (LTRN)
Always
Below 1 ohms
A12-2 (E) - Body ground
A12-3 (B) - Body ground
Always
10 kohms or higher
2009 Toyota Tundra
2009 ACCESSORIES AND EQUIPMENT Lighting - Tundra
Fig. 42: Identifying Front RH Turn Signal Light Connector Terminals
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
3. Measure the resistance according to the value(s) in the table below.
Standard resistance
FRONT TURN SIGNAL LIGHT - TURN SIGNAL FLASHER AND BODY GROUND
RH
NG: REPAIR OR REPLACE HARNESS OR CONNECTOR
OK: PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS
TABLE
5. CHECK HARNESS AND CONNECTOR (REAR COMBINATION LIGHT - TURN SIGNAL
FLASHER AND BODY GROUND)
a. for LH:
1. Disconnect the R5 light connector.
2. Disconnect the J29 relay connector.
Tester Connection
Condition Specified Condition
A13-3 (B) - J29-17 (RTRN)
Always
Below 1 ohms
A13-2 (E) - Body ground
A13-3 (B) - Body ground
Always
10 kohms or higher
2009 Toyota Tundra
2009 ACCESSORIES AND EQUIPMENT Lighting - Tundra
Fig. 43: Identifying Rear Combination Light Connector Terminals - LH
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
3. Measure the resistance according to the value(s) in the table below.
Standard resistance
REAR COMBINATION LIGHT - TURN SIGNAL FLASHER AND BODY GROUND
LH
b. for RH:
1. Disconnect the R4 light connector.
2. Disconnect the J29 relay connector.
Tester Connection
Condition Specified Condition
R5-5 (TRN) - J29-2 (LL)
Always
Below 1 ohms
R5-6 (E) - Body ground
R5-5 (TRN) - Body ground Always
10 kohms or higher
2009 Toyota Tundra
2009 ACCESSORIES AND EQUIPMENT Lighting - Tundra
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст