Toyota Tundra. Manual — part 497
2. CHECK DTC
a. Reconnect the K16 amplifier connector.
b. Check if DTC 74-40 is output.
OK: DTC 74-40 is not output.
NG: Go to step 7
OK: Go to Next Step
3. CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER - SPEAKERS)
a. Disonnect the K17 amplifier connector.
b. Disconnect the N10, M8, K14 and P14 speaker connectors.
2009 Toyota Tundra
2009 ACCESSORIES AND EQUIPMENT Navigation - Tundra
Fig. 108: Identifying N10, M8, K14 And P14 Speaker Connectors
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
c. Measure the resistance according to the value(s) in the table below.
Standard resistance
HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER - SPEAKERS)
TESTER CONNECTION SPECIFIED CONDITION
Tester Connection
Condition Specified Condition
K17-1(WFL-)-N10-2
2009 Toyota Tundra
2009 ACCESSORIES AND EQUIPMENT Navigation - Tundra
NG: REPAIR OR REPLACE HARNESS OR CONNECTOR
OK: Go to Next Step
4. INSPECT FRONT NO. 1 SPEAKER LH
a. Disconnect the N10 speaker connector.
b. Measure the resistance according to the value(s) in the table below.
Standard resistance
FRONT NO. 1 SPEAKER LH TESTER CONNECTION SPECIFIED CONDITION
K17-2(WFL+)-N10-1
Always
Below 1 ohms
K17-3(WFR-)-M8-2
K17-9 (WFR+)-M8-1
K17-4(CTR+)-K14-1
K17-10(CTR-)-K14-2
K17-5(WF1+)-P14-1
K17-12(WF1-)-P14-2
K17-2 (WFL+)-Body ground
Always
10 kohms or higher
K17-1(WFL-)-Body ground
K17-9(WFR+)-Body ground
K17-3 (WFR-)-Body ground
K17-5(WF1+)-Body ground
K17-12(WF1-)-Body ground
K17-4(CTR+)-Body ground
K17-10(CTR-)-Body ground
Tester Connection Condition Specified Condition
1-2
Always
1.5 to 2.1 ohms
2009 Toyota Tundra
2009 ACCESSORIES AND EQUIPMENT Navigation - Tundra
Fig. 109: Identifying Front No. 1 Speaker LH Connector Terminal
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
NG: REPLACE FRONT NO. 1 SPEAKER LH (See REMOVAL )
OK: Go to Next Step
5. INSPECT FRONT NO. 1 SPEAKER RH
a. Disconnect the M8 speaker connector.
b. Measure the resistance according to the value(s) in the table below.
Standard resistance
FRONT NO. 1 SPEAKER RH
Fig. 110: Identifying Front No. 1 Speaker RH Connector Terminal
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
NG: REPLACE FRONT NO. 1 SPEAKER RH (See REMOVAL )
OK: Go to Next Step
6. INSPECT FRONT NO. 4 SPEAKER
a. Disconnect the K14 speaker connector.
b. Measure the resistance according to the value(s) in the table below.
Standard resistance
FRONT NO. 4 SPEAKER TESTER CONNECTION SPECIFIED CONDITION
Tester Connection Condition Specified Condition
1-2
Always
1.5 to 2.1 ohms
2009 Toyota Tundra
2009 ACCESSORIES AND EQUIPMENT Navigation - Tundra
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст