Toyota Tundra. Manual — part 163
Fig. 73: Speaker (Independent Amplifier) - Wiring Diagram (2 Of 2)
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
INSPECTION PROCEDURE
1. CHECK SPEAKER
a. Check the malfunctioning speakers.
Result:
RESULT REFERENCE
B: Go to step 11
Result
Proceed to
Malfunction in front speaker area
A
Malfunction in rear speaker area
B
2009 Toyota Tundra
2009 ACCESSORIES AND EQUIPMENT Audio/Visual - Tundra
A: Go to Next Step
2. CHECK SPEAKER
a. Check the malfunctioning speakers.
Result:
RESULT REFERENCE
B: Go to step 5
C: Go to step 7
D: Go to step 9
A: Go to Next Step
3. INSPECT FRONT NO. 1 SPEAKER
a. Disconnect the M8 and N10 speaker connectors.
b. Measure the resistance according to the value(s) in the table below.
Standard resistance
TESTER CONNECTION SPECIFIED CONDITION
NG: REPLACE FRONT NO. 1 SPEAKER (see REMOVAL )
Fig. 74: Identifying Front No. 1 Speaker Connector Terminals
Result
Proceed to
Front No. 1 speaker
A
Front No. 2 speaker
B
Front No. 3 speaker
C
Front No. 4 speaker
D
Tester Connection Condition Specified Condition
1 - 2
Always
1.5 to 2.1 ohms
2009 Toyota Tundra
2009 ACCESSORIES AND EQUIPMENT Audio/Visual - Tundra
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
OK: Go to Next Step
4. CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER - FRONT NO. 1
SPEAKER)
a. Disconnect the M8 and N10 speaker connectors.
b. Disconnect the K17 amplifier connector.
c. Measure the resistance according to the value(s) in the table below.
Standard resistance:
for LH
TESTER CONNECTION SPECIFIED CONDITION
for RH
TESTER CONNECTION SPECIFIED CONDITION
Tester Connection
Condition Specified Condition
K17-2(WFL+) - N10-1
Always
Below 1 ohms
K17-1(WFL-) - N10-2
K17-2 (WFL+) - Body ground
Always
10 kohms or higher
K17-1 (WFL-) - Body ground
Tester Connection
Condition Specified Condition
K17-9 (WFR+) - M8-1
Always
Below 1 ohms
K17-3(WFR-) - M8-2
K17-9(WFR+) - Body ground
Always
10 kohms or higher
K17-3(WFR-) - Body ground
2009 Toyota Tundra
2009 ACCESSORIES AND EQUIPMENT Audio/Visual - Tundra
Fig. 75: Checking Harness And Connector (Stereo Component Amplifier - Front No. 1
Speaker)
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
NG: REPAIR OR REPLACE HARNESS OR CONNECTOR
OK: REPLACE STEREO COMPONENT AMPLIFIER (see REMOVAL )
5. INSPECT FRONT NO. 2 SPEAKER
a. Disconnect the K10 and K12 speaker connectors.
b. Measure the resistance according to the value(s) in the table below.
Standard resistance
TESTER CONNECTION SPECIFIED CONDITION
NG: REPLACE FRONT NO. 2 SPEAKER (see REMOVAL )
Tester Connection Condition Specified Condition
1 - 3
Always
Below 1 ohms
2 - 4
3 - 4
Always
1.3 to 2.3 ohms
2009 Toyota Tundra
2009 ACCESSORIES AND EQUIPMENT Audio/Visual - Tundra
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст