Toyota Tundra. Manual — part 724
a. Disconnect the N2 master switch connector.
b. Disconnect the O5 switch connector.
c. Measure the resistance according to the value(s) in the table below.
Standard resistance
STANDARD RESISTANCE TESTER CONNECTION SPECIFIED CONDITION
NG: REPAIR OR REPLACE HARNESS OR CONNECTOR
OK: Go to Next Step
6. CHECK POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY
a. Remove the master switch (see REMOVAL ).
b. Reconnect the master switch connector.
c. Measure the voltage according to the value(s) in the table below.
Standard voltage
STANDARD VOLTAGE TESTER CONNECTION SPECIFIED CONDITION
Tester Connection
Condition Specified Condition
N2-10 (U) - O5-5 (SU)
Always
Below 1 ohms
N2-18 (D) - O5-2 (SD)
N2-10 (U) or O5-5 (SU) - Body ground
Always
10 kohms or higher
N2-18 (D) or O5-2 (SD) - Body ground
Tester
Connection
Switch Condition
Specified
Condition
N2-10 (U) - N2-1
(E)
Ignition switch ON, rear RH side door power window
regulator switch OFF --> UP
Below 1 V --> 11 to
14 V
N2-18 (D) - N2-1
(E)
Ignition switch ON, rear RH side door power window
regulator switch OFF --> DOWN
2009 Toyota Tundra
2009 ACCESSORIES AND EQUIPMENT Windshield/WindowGlass - Tundra
Fig. 35: Identifying N2 Master Switch Connector Terminals
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
NG: REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY (see
REMOVAL )
OK: Go TO POWER WINDOWS DO NOT OPERATE AT ALL
DRIVER SIDE POWER WINDOW AUTO DOWN FUNCTION DOES NOT OPERATE
DESCRIPTION
If the AUTO DOWN function does not operate, the cause may be one or more of the following:
The power window regulator master switch has a malfunction.
The front power window regulator motor LH (for driver side) has a malfunction.
The wiring between the power window regulator master switch and the front power window regulator
motor LH (for driver side) is open or shorted.
WIRING DIAGRAM
2009 Toyota Tundra
2009 ACCESSORIES AND EQUIPMENT Windshield/WindowGlass - Tundra
Fig. 36: Driver Side Power Window Auto Down Function Does Not Operate Wiring Diagram
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
INSPECTION PROCEDURE
1. CHECK MANUAL UP / DOWN FUNCTION
a. Check that the manual UP/DOWN function of the power window regulator master switch can
operate the driver door power window.
OK: Manual UP/DOWN function operates normally.
NG: OTHER PROBLEM (see DRIVER SIDE POWER WINDOW DOES NOT OPERATE WITH
POWER WINDOW MASTER SWITCH )
OK: REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY (see
REMOVAL )
POWER WINDOWS DO NOT OPERATE AT ALL
DESCRIPTION
If all of the power windows do not operate, the power window regulator master switch may have no power or
may be malfunctioning.
WIRING DIAGRAM
2009 Toyota Tundra
2009 ACCESSORIES AND EQUIPMENT Windshield/WindowGlass - Tundra
Fig. 37: Power Windows Do Not Operate At All Wiring Diagram
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
INSPECTION PROCEDURE
1. CHECK HARNESS AND CONNECTOR (MASTER SWITCH - BATTERY AND BODY
GROUND)
a. Disconnect the N2 master switch connector.
b. Measure the voltage of the wire harness side connector.
Standard voltage
for Regular Cab:
MASTER SWITCH - BATTERY AND BODY GROUND VOLTAGE (FOR REGULAR
CAB)
for Double Cab:
MASTER SWITCH - BATTERY AND BODY GROUND VOLTAGE (FOR DOUBLE CAB)
for CrewMax:
MASTER SWITCH - BATTERY AND BODY GROUND VOLTAGE (FOR CREWMAX)
Tester Connection
Switch Condition Specified Condition
N2-15 (B) - Body ground Ignition switch ON
11 to 14 V
Tester Connection
Switch Condition Specified Condition
N2-6 (B) - Body ground Ignition switch ON
11 to 14 V
Tester Connection
Switch Condition Specified Condition
N2-6 (B) - Body ground Ignition switch ON
11 to 14 V
2009 Toyota Tundra
2009 ACCESSORIES AND EQUIPMENT Windshield/WindowGlass - Tundra
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст