Toyota Tundra. Manual — part 2041
Fig. 346: Identifying Valve Rocker Arm Position
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
21
INSTALL CAMSHAFT BEARING CAP RH
a
Apply a light coat of engine oil to the camshaft journals, camshaft housings and bearing caps
b
Install the No 1 and No 2 camshafts to the camshaft housing
c
Confirm the marks and numbers on the camshaft bearing caps and place them in their proper
positions and directions
Fig. 347: Identifying Camshaft Bearing Caps Mark And Number
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
d
Temporarily install the 10 bolts in the order shown in the illustration
Fig. 348: Identifying Camshaft Bearing Cap Bolts Tightening Order
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
2009 Toyota Tundra
2009 ENGINE Engine Mechanical (3UR-FE) - Tundra
22
INSTALL CAMSHAFT HOUSING SUB-ASSEMBLY RH
a
Make sure that the valve rocker arms are installed as shown in the illustration
Fig. 349: Identifying Proper Position For Installing Valve Rocker Arms
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
b
Apply seal packing in a continuous line as shown in the illustration
Seal packing: Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent
Standard seal diameter: 3.5 to 4.0 mm (0.138 to 0.157 in.)
c
Install the camshaft housing, and install the 18 bolts in the order shown in the illustration
Torque: for bolt A
10 N*m (102 kgf*cm, 7 ft.*lbf)
for except bolt A
NOTE:
Remove any oil from the contact surface.
Install the camshaft housing within 3 minutes and tighten the
bolts within 15 minutes after applying seal packing.
Fig. 350: Identifying Seal Packing Areas On Camshaft Housing
Sub-Assembly - RH
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
2009 Toyota Tundra
2009 ENGINE Engine Mechanical (3UR-FE) - Tundra
30 N*m (306 kgf*cm, 22 ft.*lbf)
d
Tighten the 10 bolts in the order shown in the illustration
Torque: 16 N*m (163 kgf*cm, 12 ft.*lbf)
Fig. 352: Identifying Camshaft Housing Bolts Tightening Order
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
23
INSTALL CAMSHAFT BEARING CAP LH
a
Apply a light coat of engine oil to the camshaft journals, camshaft housings and bearing caps
b
Install the No 3 and No 4 camshafts to the camshaft housing
c
Confirm the marks and numbers on the camshaft bearing caps and place them in their proper
positions and directions
NOTE:
Do not start the engine for at least 2 hours after the installation.
Make sure that the knock pin of the camshaft is positioned as
shown in the illustration before installing the camshaft housing.
Fig. 351: Identifying Camshaft Housing Bolts Installing Order
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
NOTE:
Thoroughly wipe clean any seal packing.
2009 Toyota Tundra
2009 ENGINE Engine Mechanical (3UR-FE) - Tundra
Fig. 353: Identifying Marks And Numbers On Camshaft Bearing Caps
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
d
Temporarily install the 10 bolts in the order shown in the illustration
Fig. 354: Identifying Camshaft Bearing Cap Bolts Installing Order
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
24
INSTALL CAMSHAFT HOUSING SUB-ASSEMBLY LH
a
Install the valve rocker arms as shown in the illustration
Fig. 355: Identifying Proper Position For Installing Valve Rocker Arms
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
b
Apply seal packing in a continuous line as shown in the illustration
Seal packing: Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent
2009 Toyota Tundra
2009 ENGINE Engine Mechanical (3UR-FE) - Tundra
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст