Toyota Tundra. Manual — part 696
9. INSTALL SLIDE AND VERTICAL POWER SEAT SWITCH KNOB LH (see REASSEMBLY )
10. INSTALL FRONT SEAT ASSEMBLY LH
a. Install the front seat (see INSTALLATION ).
SEAT HEATER CONTROL (W/ SEAT HEATER SYSTEM)
ON-VEHICLE INSPECTION
1. INSPECT SEAT HEATER CONTROL SUB-ASSEMBLY LH
a. Disconnect the Z11 connector.
b. Measure the resistance according to the value(s) in the table below.
Standard resistance
SEAT HEATER CONTROL SUB-ASSEMBLY LH RESISTANCE SPECIFICATION
DISCONNECT
Fig. 599: Identifying Seat Heater Control Connector Terminals (LH)
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
If the result is not as specified, there may be a malfunction on the wire harness side.
c. Measure the voltage according to the value(s) in the table below.
Standard voltage
SEAT HEATER CONTROL SUB-ASSEMBLY LH VOLTAGE SPECIFICATION
DISCONNECT
Tester Connection
Specified Condition
Z11-6 (E) - Body ground
Below 1 ohms
2009 Toyota Tundra
2009 ACCESSORIES AND EQUIPMENT Seat - Tundra
If the result is not as specified, there may be a malfunction on the wire harness side.
d. Connect the Z11 connector.
e. Measure the voltage according to the value(s) in the table below.
Standard voltage
SEAT HEATER CONTROL SUB-ASSEMBLY LH VOLTAGE SPECIFICATION
CONNECT
If the result is not as specified, the seat heater control may have a malfunction.
Fig. 600: Identifying Seat Heater Control Connector Terminals (LH)
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
2. INSPECT SEAT HEATER CONTROL SUB-ASSEMBLY RH
a. Disconnect the Y8 connector.
b. Measure the resistance according to the value(s) in the table below.
Standard resistance
SEAT HEATER CONTROL SUB-ASSEMBLY RH RESISTANCE SPECIFICATION
DISCONNECT
Tester Connection
Switch Condition
Specified Condition
Z11-1 (SWL) - Z11-6(E)
Ignition switch ON, seat heater switch OFF
Below 1 V
Ignition switch ON, seat heater switch ON
11 to 14 V
Z11-4(B) - Z11-6(E)
Ignition switch OFF
Below 1 V
Ignition switch ON
11 to 14 V
Tester Connection
Switch Condition
Specified Condition
Z11-5 (THL) - Body
ground
Ignition switch ON, seat heater switch
ON, volume MIN --> MAX
Gradual increase between below
1 V and 11 to 14 V
Tester Connection
Specified Condition
Y8-6 (E) - Body ground
Below 1 ohms
2009 Toyota Tundra
2009 ACCESSORIES AND EQUIPMENT Seat - Tundra
If the result is not as specified, there may be a malfunction on the wire harness side.
c. Measure the voltage according to the value(s) in the table below.
Fig. 601: Identifying Seat Heater Control Connector Terminals (RH)
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
Standard voltage
SEAT HEATER CONTROL SUB-ASSEMBLY RH VOLTAGE SPECIFICATION
DISCONNECT
If the result is not as specified, there may be a malfunction on the wire harness side.
d. Connect the Y8 connector.
e. Measure the voltage according to the value(s) in the table below.
Standard voltage
SEAT HEATER CONTROL SUB-ASSEMBLY RH VOLTAGE SPECIFICATION
CONNECT
Tester Connection
Switch Condition
Specified Condition
Y8-1 (SWL) - Y8-6 (E)
Ignition switch ON, seat heater switch OFF
Below 1 V
Ignition switch ON, seat heater switch ON
11 to 14 V
Y8-4(B1) - Y8-6(E)
Ignition switch OFF
Below 1 V
Ignition switch ON
11 to 14 V
Tester Connection
Condition
Specified Condition
Y8-5 (THL) - Body
ground
Ignition switch ON, seat heater switch
ON, volume MIN --> MAX
Gradual increase between below 1
V and 11 to 14 V
2009 Toyota Tundra
2009 ACCESSORIES AND EQUIPMENT Seat - Tundra
If the result is not as specified, the seat heater control may have a malfunction.
Fig. 602: Identifying Seat Heater Control Connector Terminals (RH)
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
2009 Toyota Tundra
2009 ACCESSORIES AND EQUIPMENT Seat - Tundra
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст