Toyota Proace City EV (2022 year). Manual in english — page 10
180
Rear parking sensors
which increases as the vehicle approaches the
When the obstacle is very close, the "Danger"
obstacle.
symbol is displayed on the screen.
► Engage reverse gear to start the system
When the distance between the vehicle and the
(confirmed by an audible signal).
obstacle becomes less than about 30 cm (0 ft
Front parking sensors
The system is switched off when reverse gear is
11"), the audible signal becomes continuous.
In addition to the rear parking sensors, the front
disengaged.
The sound emitted by the speaker (right or
parking sensors are triggered when an obstacle
Audible assistance
left) indicates the side on which the obstacle is
is detected in front and the speed of the vehicle
located.
is still below 10 km/h (6 mph).
The front parking sensors are interrupted if the
NOTICE
vehicle stops for more than three seconds in
forward gear, if an obstacle is no longer detected
Adjusting the audible signal
or when the speed of the vehicle exceeds
With TOYOTA Connect Radio or
10 km/h (6 mph).
TOYOTA Connect Nav, pressing this
button opens the window for adjusting the
NOTICE
The system signals the presence of obstacles
volume of the audible signal.
which are both within the sensors’ detection zone
The sound emitted by the speaker (front or
and in the vehicle path defined by the direction of
rear) locates the obstacle in relation to the
Visual assistance
the steering wheel.
vehicle, in the vehicle trajectory, in front or
behind.
It supplements the audible assistance, without
Depending on version, in the example shown,
taking account of the vehicle's trajectory, by
only the obstacles present in the shaded area
displaying bars on the screen that represent the
will be signalled by the audible assistance.
distance between the obstacle and the vehicle
The proximity information is given by an
(white: more distant obstacles, orange: close
intermittent audible signal, the frequency of
obstacles, red: very close obstacles).
181
Side parking sensors
Deactivation / Activation
NOTICE
Without touch screen
The rear parking sensors system will be
deactivated automatically if a trailer or bicycle
carrier is connected to a towing device
installed in accordance with the
6
manufacturer's recommendations.
In this case, the outline of a trailer is displayed
at the rear of the image of the vehicle.
Using four additional sensors located on the
sides of the front and rear bumpers, the system
The parking sensors are deactivated while the
records the position of fixed obstacles during
Park Assist function is measuring a space.
► To deactivate or activate the system, press
the manoeuvre and signals them when they are
For more information on the Park Assist, refer
this button.
located by the sides of the vehicle.
to the corresponding section.
The indicator lamp is lit when the system is
WARNING
deactivated.
Operating limits
With touch screen
If the boot is heavily loaded, the vehicle may tilt,
Only fixed obstacles are signalled correctly.
The settings are changed via the
affecting distance measurements.
Moving obstacles detected at the beginning of
Driving / Vehicle touch screen
the manoeuvre may be signalled mistakenly,
Malfunction
menu.
while moving obstacles which appear at the
The state of the system stays in the memory
In the event of a malfunction when
sides of the vehicle and which were not
when the ignition is switched off.
changing into reverse gear, this warning
previously recorded will not be signalled.
lamp lights up on the instrument panel,
accompanied by the display of a message and
WARNING
an audible signal (short beep).
Have it checked by any authorized Toyota
The objects memorised during the manoeuvre
retailer or Toyota authorized repairer, or any
will no longer be stored after switching off the
reliable repairer.
ignition.
182
Reversing camera
WARNING
Certain vehicles may be difficult to see (dark
colours, lamps off) when the brightness of the
screen is reduced using the vehicle’s lighting
WARNING
dimmer.
For more information, refer to the General
recommendations on the use of driving
The blue lines 1 represent the general direction
WARNING
and manoeuvring aids.
of the vehicle (the gap corresponds to the width
The image quality may be affected by the
of your vehicle with the mirrors).
With the ignition on, this system uses a camera
surroundings, the exterior conditions (rain,
The red line 2 represents a distance of about
located near the third brake lamp to display
dirt, dust), the driving mode and the lighting
30 cm (0 ft 11") beyond the edge of your
a view of the rear of your vehicle on the
conditions (night, low sun).
vehicle's rear bumper.
reproduction screen (if it is a panel van or has a
In the presence of areas in shade, or in
The green lines 3 represent distances of about
solid partition).
conditions of bright sunlight or inadequate
1 and 2 metres (3 ft 3" and 6 ft 6") beyond the
The reversing camera is activated automatically
lighting, the image may be darkened and with
edge of your vehicle's rear bumper.
when reverse gear is engaged. The image
lower contrast.
The turquoise blue curves 4 represent the
is displayed on the reproduction screen. The
maximum turning circle.
reproduction screen switches off when the
gearbox is in neutral or in a forward gear.
WARNING
WARNING
Obstacles may appear further away than they
Some objects may not be seen by the
actually are.
camera.
During parking manoeuvres and lane
changes, it is important to check the sides of
the vehicle using the mirrors.
The rear parking sensors also supplement the
information on the vehicle's surroundings.
183
Operating limits
Surround Rear Vision
The system may be disrupted (or even
damaged) and not work in the following
situations:
- Installation of a bicycle carrier on the tailgate
WARNING
or side-hinged door (depending on version).
6
- Attachment of a trailer to the towball.
For more information, refer to the General
- Driving with a door open.
recommendations on the use of driving
and manoeuvring aids.
WARNING
- Passenger side view: shows the area at the
With the ignition on, in order to improve visibility
passenger side of the vehicle.
Please note, the camera must not be
of the passenger side blind spot and the rear
The orange line 1 represents a distance of 5 m
obscured (by a sticker, a bicycle carrier, etc.).
of the vehicle, this system uses two cameras
(16 ft 4") from the rear bumper.
to display the views of the vehicle’s close
NOTICE
surroundings on the reproduction screen (panel
van or fitted with a solid partition).
The field of vision of the camera may vary
This system has three sub-functions:
depending on the load in vehicle.
Maintenance
recommendations
In bad or wintry weather, ensure that the camera
is not covered by mud, frost or snow.
Check the cleanliness of the camera lens
regularly.
If necessary, clean the camera with a soft, dry
cloth.
When washing the vehicle using a high-pressure
- Surveillance rear view: shows a long-
jet, keep the spray directed at least 30 cm (0 ft
distance view of the area at the rear.
11") away from the camera.
The orange line 1 represents a distance of 5 m
(16 ft 4") from the rear bumper.
184
WARNING
WARNING
Please routinely check your exterior mirrors
Obstacles may appear further away than they
while driving and during manoeuvres.
actually are.
During parking manoeuvres and lane
changes, it is important to check the sides of
WARNING
the vehicle using the mirrors.
The rear parking sensors also supplement the
Some items may not be seen by the rear
information on the vehicle's surroundings.
camera.
Activation / Deactivation
WARNING
The system starts when the ignition is switched
Certain vehicles may be difficult to see (dark
on.
colours, lamps off) when the brightness of the
screen is reduced using the vehicle’s lighting
- Visual reversing assistance: shows a view
dimmer.
of the area close to the rear of the vehicle.
The blue dimension lines 1 represent the width
of your vehicle with the mirrors unfolded.
WARNING
The red line 2 represents a distance of 30 cm (0
ft 11") from the rear bumper; the two green lines
The image quality may be affected by the
3 and 4 represent 1 m (3 ft 3") and 2 m (6 ft 6"),
environment, the exterior conditions (rain, dirt,
respectively.
dust), the driving mode and the lighting
The blue curves 5 appear successively; they
conditions (night, low sun).
are based on the position of the steering wheel
In the presence of areas in shade, or in
and represent the turning circle radius of your
conditions of bright sunlight or inadequate
vehicle.
lighting, the image may be darkened and with
► With the ignition on, press button 2 to switch
The orange dashes 6 represent the opening radii
lower contrast.
the reproduction screen on / off.
of the rear doors.
A message appears.
► Take note of this message and validate
with button 1 corresponding to the “Accept”
response.
185
The reproduction screen comes on.
NOTICE
► With the engine running, press button 2 to
switch the reproduction screen off.
The field of vision of the rear camera
(surveillance rear view and visual
NOTICE
reversing aid) may vary depending on the
load in the vehicle.
The function is automatically paused (the
6
reproduction screen becomes grey) in
reverse, above 15 km/h (9 mph).
NOTICE
The function restarts when the vehicle is
once more travelling at a speed below this
If the side-hinged door is opened during use
threshold.
of the surveillance rear view or the visual
aid for reversing, in forward gear or reverse
gear, the output screen becomes grey.
Operation
NOTICE
If the front passenger door is opened during
► In neutral, the monitoring rear view is
use of the passenger side view, in forward
The area around the vehicle is shown by the
displayed by default.
gear or reverse gear, the output screen
monitoring rear view and the passenger
► When reverse is engaged, the visual
becomes grey.
side view only.
reversing aid is displayed on the screen (even if
it is switched off).
NOTICE
Operating limits
The system may be disrupted (or even
If a trailer is attached to the towball, when
damaged) and not work in the following
reverse gear is engaged the visual reversing
situations:
aid will no longer work until the trailer is
- Installation of a bicycle carrier on the tailgate
disconnected. The surveillance rear view
or side-hinged door (depending on version).
becomes the default view.
- Attachment of a trailer to the towball.
- Driving with a door open.
NOTICE
WARNING
► To change the view, press the end of the
If the system develops a malfunction, go to a
lighting control stalk or press the corresponding
TOYOTA dealer to avoid any safety problems.
Please note, the cameras must not be
button located below the screen.
obscured (by a sticker, a bicycle carrier, etc.).
186
The screen is divided into two parts with a
between the brackets) in real time and as the
Top Rear Vision
contextual view and a view from above the
manoeuvre progresses.
vehicle in its close surroundings.
It facilitates the alignment of your vehicle when
The parking sensors supplement the information
parking and allows obstacles close to the vehicle
Refer to the General recommendations on the
on the view from above the vehicle.
to be seen. It is automatically deleted if the
use of driving and manoeuvring aids.
Various contextual views may be displayed:
vehicle remains stationary for too long.
- Standard view.
- 180° view.
Rear vision
- Zoom view.
AUTO mode is activated by default.
In this mode, the system chooses to display the
best view (standard or zoom).
You can change the type of view at any time
during a manoeuvre.
As soon as reverse gear is engaged with the
The state of the function is not saved when the
engine running, this system displays views of
ignition is switched off.
your vehicle’s close surroundings on the touch
screen using a camera located at the rear of the
Principle of operation
vehicle.
To activate the camera, located on the tailgate,
engage reverse and keep the speed of the
vehicle below 10 km/h (6 mph).
The system is deactivated:
- Automatically, at speeds above approximately
10 km/h (6 mph),
- Automatically, if the tailgate is opened.
- Upon changing out of reverse gear (the image
remains displayed for 7 seconds).
Using the rear camera, the vehicle's close
- By pressing the white arrow in the upper-left
surroundings are recorded during manoeuvres
corner of the touch screen.
at low speed.
An image from above your vehicle in its close
surroundings is reconstructed (represented
187
AUTO mode
The blue lines 1 represent the width of your
NOTICE
vehicle, with the mirrors unfolded; their direction
changes depending on the position of the
Obstacles may appear further away than they
steering wheel.
actually are in reality.
The red line 2 represents a distance of 30 cm (0
It is important to check the sides of the
ft 11") from the rear bumper; the two blue lines 3
vehicle during the manoeuvre, using the
and 4 represent 1 m and 2 m (3 ft 3" and 6 ft 6"),
6
mirrors.
respectively.
The rear parking sensors also provide
This view is available with AUTO mode or in the
information on the vehicle's surroundings.
view selection menu.
Zoom view
180° view
This mode is activated by default.
Using sensors in the rear bumper, the automatic
view changes from the rear view (standard) to
the view from above (zoom) as an obstacle is
approached at the level of the red line (less than
30 cm (0 ft 11")) during a manoeuvre.
Standard view
The camera records the vehicle's surroundings
during the manoeuvre in order to create a
view from above the rear of the vehicle in its
near surroundings, allowing the vehicle to be
manoeuvred around obstacles nearby.
This view is available with AUTO mode or in the
The 180° view facilitates reversing out of a
view selection menu.
parking bay, making it possible to see the
approach of vehicles, pedestrians and cyclists.
The area behind the vehicle is displayed on the
This view is not recommended for carrying out a
screen.
complete manoeuvre.
188
It consists of 3 areas: left A, centre B and right
NOTICE
C.
This view is available only from the view
You can deactivate the function at any time
selection menu.
until the parking space entry or exit
manoeuvre begins, by pressing the arrow
Park Assist
located in the top left-hand corner of the
display page.
The system assists with the following
manoeuvres:
Selecting the type of manoeuvre
A. Entering a "parallel" parking space
WARNING
B. Leaving a "parallel" parking space
C. Entering a "bay" parking space
For more information, refer to the General
recommendations on the use of driving
Operation
and manoeuvring aids.
► When approaching a parking area, reduce
This system provides active parking assistance
the speed of your vehicle to 30 km/h (19 mph)
for vehicles fitted with a manual gearbox: it
or less.
detects a parking space and then steers in
the appropriate direction to park in this space
Activating the function
while the driver controls the driving direction,
The function is activated via the
engagement of gears, acceleration and braking.
Driving / Vehicle touch screen
A manoeuvre selection page is displayed on the
To assist the driver in monitoring the correct
menu.
touch screen: by default, the "Entry" page if the
manoeuvring operation, the system automatically
Select "Park Assist".
vehicle has been running since the ignition was
triggers the display of Top Rear Vision and the
switched on, otherwise, the "Exit" page.
activation of the parking sensors.
WARNING
► Select the type and side of the manoeuvre to
The system performs the measurements of
activate the parking space search.
available parking spaces and calculations of
Activating the function deactivates the Blind
The selected manoeuvre can be changed at
distances to obstacles using ultrasonic sensors
Spot Monitoring System.
any time, even while searching for an available
built into the front and rear bumpers of the
space.
vehicle.
This indicator lamp comes on to confirm
the selection.
189
Parking space search
During the manoeuvre
► You should drive at a distance of between
The system controls the vehicle’s steering. It
0.50 m and 1.50 m (1 ft 7" and 4 ft 11") from the
gives instructions on the manoeuvring direction
row of parked vehicles, without ever exceeding
when starting "parallel" entry and exit parking
30 km/h (19 mph), until the system finds an
manoeuvres, and for all "bay" entry manoeuvres.
available space.
There instructions are displayed as a symbol
6
The parking space search is suspended at
accompanied by a message:
higher speeds. The function is automatically
"Reverse".
deactivated if the vehicle speed exceeds
50 km/h (31 mph).
“Go forwards".
When the system finds an available space, "OK"
NOTICE
The manoeuvring status is indicated by these
is displayed on the parking view, accompanied
symbols:
by an audible signal.
For "parallel" parking, the space must
Manoeuvre in progress (green).
measure at least the length of your vehicle
Preparing for the manoeuvre
plus 0.60 m (1 ft 11").
Manoeuvre cancelled or finished (red)
► Move very slowly until the request to stop
For "bay" parking, the space must be at least
(the arrows indicate that the driver must
the vehicle is displayed: "Stop the vehicle“,
as wide as your vehicle plus 0.70 m (2 ft 3").
resume control of the vehicle).
accompanied by the “STOP” sign and an audible
The maximum speeds during manoeuvres are
signal.
indicated by these symbols:
NOTICE
Once the vehicle has stopped, an instructions
7 km/h or 5 mph, for parking space entry.
page is displayed on the screen.
7
If the parking sensors function has been
► To prepare for the manoeuvre, follow the
deactivated in the Driving/Vehicle touch
5 km/h or 3 mph, for parking space exit.
instructions.
5
screen menu, it will be automatically
The start of the manoeuvre is indicated by the
reactivated when the system is activated.
"Manoeuvre under way" onscreen message
and an accompanying audible signal.
Reversing is indicated by this message:
“Release the steering wheel, reverse”.
The Top Rear Vision and the parking sensors
are automatically activated to help you monitor
the area immediately surrounding your vehicle
during the manoeuvre.
190
- activating the direction indicator lamps on the
End of the parking space entry or exit
WARNING
opposite side to that of the manoeuvre.
manoeuvre
- unfastening the driver's seat belt.
During manoeuvring phases, the steering
The vehicle stops as soon as the manoeuvre is
- switching off the ignition.
wheel performs rapid turns: do not hold the
completed.
Interruption by the system:
steering wheel or put your hands between the
The manoeuvre symbol is displayed in red,
- vehicle exceeding the speed limit of 7 km/h
spokes of the steering wheel. Watch out for
accompanied by the message “Manoeuvre
(5 mph) during parking space entry manoeuvres,
any objects that could interfere with the
completed” on the touch screen.
or 5 km/h (3 mph) during parking space exit
manoeuvre (loose clothing, scarf, tie, etc.).
When the function is deactivated, this
manoeuvres.
Risk of injury!
indicator lamp goes off, accompanied by
- activation of anti-slip regulation on a slippery
It is the driver's responsibility to constantly
an audible signal.
road.
monitor the traffic, especially vehicles coming
When entering a parking space, the driver may
- opening of a door or the boot.
towards you.
be required to complete the manoeuvre.
- engine stall.
The driver should check that no objects or
- system malfunction.
people are obstructing the vehicle’s path.
- after 10 manoeuvres to enter or exit a parallel
parking space and after 7 manoeuvres to enter a
NOTICE
parking bay.
Interrupting the manoeuvre automatically
The images from the camera(s) displayed on
deactivates the function.
the touch screen may be distorted by the
The manoeuvre symbol is displayed in red,
terrain.
accompanied by the "Manoeuvre cancelled"
In shady areas, or in inadequate sunlight
message on the touch screen.
or lighting conditions, the image may be
A message prompts the driver to take back
darkened and with lower contrast
control of the vehicle.
The function is deactivated after a few
The manoeuvre can be permanently interrupted
seconds; this warning lamp goes off and
at any time, either by the driver or automatically
the function returns to the initial display.
by the system.
Interruption by the driver:
- taking over control of the steering.
191
Operating limits
Malfunctions
WARNING
- The system may suggest an inappropriate
When the function is not activated, this
parking space (parking prohibited, work in
If any of the following malfunctions occurs, do
indicator lamp will flash briefly and an
progress with damaged road surface, location
not use the system:
audible signal will be emitted to indicate a
alongside a ditch, etc.).
- If a tyre is under-inflated.
system malfunction.
- The system may indicate that a space has
- If one of the bumpers is damaged.
If the malfunction occurs while the system is in
6
been found but not offer it because of a fixed
- If one of the cameras is faulty.
use, the warning lamp goes off.
obstacle on the opposite side of the manoeuvre,
If the parking sensor malfunction occurs
which would not allow the vehicle to follow the
during use, indicated by this warning lamp
WARNING
necessary trajectory required for parking.
coming on, it causes the function to deactivate.
- The system may indicate that a space has
In the event of a malfunction, have the system
If the vehicle has undergone any of the
been found but the manoeuvre will not be
checked by a TOYOTA dealer or a qualified
following modifications, do not use the
triggered, because the width of the lane is
workshop.
function:
insufficient.
In the event of a power steering
- When carrying an object extending beyond
- The system is not designed to perform the
malfunction, this warning lamp is
the dimensions of the vehicle (ladder on the
parking manoeuvre on a sharp bend.
displayed on the instrument panel, accompanied
roof bars, bicycle carrier on the tailgate, etc.).
- The system does not detect spaces that
by a warning message.
- With a non-approved towball in place.
are much larger than the vehicle itself or that
- With snow chains fitted.
are delimited by obstacles that are too low
WARNING
- When driving on a small-diameter or
(pavements, studs, etc.) or too thin (trees, posts,
"space-saver" type spare wheel.
wire fences, etc.).
You must stop the vehicle.
- When the wheels fitted are a different size
- If the boot is heavily loaded, the tilt of the
Stop as soon as it is safe to do so and switch
from the original ones.
vehicle towards the rear may interfere with the
off the ignition.
- After modifying one or both bumpers
distance measurements.
Contact a TOYOTA dealer or a qualified
(added protection).
workshop.
- If the sensors have been repainted other
WARNING
than by the TOYOTA dealer network.
- With sensors not approved for the vehicle.
Do not use the function under the following
exterior conditions:
- Alongside a soft shoulder (e.g. ditch) or
quay or on the edge of a drop.
- When the road surface is slippery (e.g. ice).
192
Compatibility of fuels
Diesel at low temperature
Refuelling
At temperatures below 0 °C (+32 °F), the
Fuel tank capacity: approximately 61 litres
formation of paraffins in summer-type Diesel
(petrol) or 50 litres (Diesel).
fuels could prevent the engine from operating
Petrol fuels conforming to the EN228 standard
Reserve level: approximately 6 litres.
correctly. In these temperature conditions, use
containing up to 5% and 10% ethanol
winter-type Diesel fuel and keep the fuel tank
Low fuel level
respectively.
more than 50 % full.
1
When the low fuel level is reached,
1/2
At temperatures below -15 °C (+5 °F) to avoid
this warning lamp comes on on the
problems starting, it is best to park the vehicle
instrument panel, accompanied by an onscreen
Diesel fuels conforming to the EN590, EN16734
under shelter (heated garage).
message and an audible signal. When it first
and EN16709 standards and containing up to
comes on, about 6 litres of fuel remain in the
7%, 10%, 20% and 30% fatty acid methyl ester
Travelling abroad
tank.
respectively. The use of B20 or B30 fuels, even
Certain fuels could damage your vehicle’s
Until sufficient fuel is added, this warning lamp
occasionally, imposes special maintenance
engine.
appears every time the ignition is switched on,
conditions referred to as "Arduous conditions".
In certain countries, the use of a particular
accompanied by an onscreen message and
fuel may be required (specific octane rating,
an audible signal. When driving, this message
specific trade name, etc.) to ensure correct
and audible signal are repeated with increasing
Paraffinic Diesel fuel conforming to the EN15940
operation of the engine.
frequency as the fuel level drops towards 0.
standard.
For all additional information, consult a dealer.
You must refuel as soon as possible to avoid
running out of fuel.
WARNING
For more information on Running out of fuel
(Diesel), refer to the corresponding section.
The use of any other type of (bio) fuel
(vegetable or animal oils, pure or diluted,
NOTICE
domestic fuel, etc.) is strictly prohibited (risk
of damage to the engine and fuel system).
A small arrow by the warning lamp indicates
which side of the vehicle the fuel filler flap is
NOTICE
located on.
The only fuel additives authorised for use are
those that meet the B715001 (petrol) or
B715000 (Diesel) standards.
193
WARNING
Stop & Start
Never refuel with the engine in STOP mode;
WARNING
you must switch off the ignition.
If the vehicle is equipped with a sliding door
7
Refuelling
on its left-hand side, do not open it while the
fuel filler flap is open. Otherwise, there is a
At least 10 litres of fuel must be added, in order
risk that the fuel filler flap and the sliding door
to be registered by the fuel gauge.
may be damaged and the person filling up
Opening the filler cap may create a noise caused
► Unscrew and remove the filler cap, then
may be injured.
by an inrush of air. This is entirely normal and
place it on the holder located on the fuel filler
results from the sealing of the fuel system.
flap.
To refuel in complete safety:
► Insert the nozzle and push it in fully (while
► Always switch off the engine.
pushing on the metal valve A).
► Unlock the vehicle using the Keyless Entry
► Fill the tank. Do not continue past the
WARNING
and Starting.
third cut-off of the nozzle, as this may cause
► Open the fuel filler flap.
malfunctions.
If the fuel filler flap is open, a device prevents
► Put the filler cap back in place and close it by
the left-hand side door from opening.
turning to the right.
The door can be opened half-way, however.
► Push the fuel filler flap to close it (your
Close the fuel filler flap to regain use of the
vehicle must be unlocked).
door.
► With a conventional key, insert the key into
the filler cap, then turn the key to the left.
194
Fuel cut-off
NOTICE
Your vehicle is fitted with a safety system that
cuts off the supply of fuel in the event of an
The misfuel prevention device does not
impact.
prevent filling with a jerrycan, regardless of
WARNING
the fuel type.
Misfuel prevention (Diesel)
If the fuel filler flap is open, a device prevents
the left-hand side door from opening.
(Depending on country of sale.)
NOTICE
The door can be opened half-way, however.
This mechanical device prevents filling the tank
Close the fuel filler flap to regain use of the
of a Diesel vehicle with petrol.
Travelling abroad
door.
Located in the filler neck, the misfuel prevention
As Diesel fuel pump nozzles may be different
device appears when the filler cap is removed.
in other countries, the presence of the misfuel
The vehicle is fitted with a catalytic converter,
prevention device may make refuelling
which helps to reduce the level of harmful
Operation
impossible.
emissions in the exhaust gases.
Before travelling abroad, it is advisable to
check with a TOYOTA dealer if the vehicle is
WARNING
suitable for the distribution equipment of the
countries visited.
If you have put in the wrong fuel for your
vehicle, you must have the fuel tank
drained and filled with the correct fuel
before starting the engine.
When a petrol filler nozzle is inserted into the
fuel filler neck of a Diesel vehicle, it comes into
contact with the flap. The system remains closed
and prevents filling.
Do not persist but introduce a Diesel type
filler nozzle.
195
burns or potentially fatal electric shock
Stop as soon as it is safe to do so and switch
Charging system
(short-circuit/electrocution)!
off the ignition.
(Electric)
In the event of a problem, always contact
Contact any authorized Toyota retailer or
any authorized Toyota retailer or Toyota
Toyota authorized repairer, or any reliable
400 V electrical system
authorized repairer, or any reliable repairer.
repairer.
The electrical traction system, which operates at
7
a voltage of approximately 400 V, is identified by
WARNING
orange cables, and its components are marked
with this symbol:
In the event of exposure to a fire
Immediately exit and evacuate all passengers
from the vehicle. Never attempt to fight the
fire yourself - risk of electrocution!
You must immediately contact the emergency
services, informing them that the incident
involves an electric vehicle.
WARNING
WARNING
This label is intended solely for use by
WARNING
An electric vehicle’s power train can become
firefighters and maintenance services in the
hot during use and after switching off the
When washing
event of any work on the vehicle.
ignition.
Before washing the vehicle, always check that
No other person must touch the device shown
Comply with the warning messages shown on
the charging flap is closed correctly.
on this label.
labels, particularly inside the charging flap.
Never wash the vehicle while the battery is
on charge.
WARNING
WARNING
In the event of an accident or impact to the
In the event of a problem
vehicle’s underbody
All work on or modifications to the vehicle’s
In these situations, the electrical circuit or the
electrical system (including the traction
traction battery can be seriously damaged.
battery, connectors, orange cables and
other components visible from the interior or
exterior) is strictly prohibited - risk of severe
196
Charging connectors and
WARNING
NOTICE
indicator lamps
High-pressure washing
The traction battery ageing process is
To avoid damaging the electrical components,
influenced by multiple factors, including
it is expressly prohibited to use high-pressure
climate conditions, the distance travelled and
washing in the engine compartment or under
how often it has been fast-charged.
the body.
Do not use a pressure greater than 80 bar
WARNING
when washing the bodywork.
In the event of damage to the traction
WARNING
battery
It is strictly prohibited to work on the vehicle
Never allow water or dust to enter the
yourself.
connector or charging nozzle - risk of
Do not touch liquids coming from the battery,
electrocution or fire!
and in the event of skin contact with these
Never connect / disconnect the charging
products, wash abundantly with water and
1.
Charging connectors
nozzle or cable with wet hands - risk of
contact a doctor as soon as possible.
2.
Deferred charging activation button
electrocution!
Contact any authorized Toyota retailer or
3.
Nozzle locking indicator lamp
Toyota authorized repairer, or any reliable
Fixed red: nozzle positioned correctly and
repairer to have the system checked.
locked in the connector.
Traction battery
Flashing red: nozzle incorrectly positioned or
This battery stores the energy that powers
locking not possible.
the electric motor and the thermal comfort
4.
Charging indicator lamp
equipment in the passenger compartment. It is
discharged during use, and must therefore be
regularly recharged. There is no need to wait
for the traction battery to fall to its reserve level
before recharging.
Battery life may vary according to the type of
driving, the route, thermal comfort equipment
usage and battery component ageing.
197
Identification labels on charging
State of charging
Meaning
WARNING
sockets/connectors
indicator lamp
In case of impact, even light, against the
Identification labels are affixed to the vehicle,
Fixed white
Guide lighting
charging flap, do not use it.
charging cable and charger to inform the user
on opening the
Do not dismantle or modify the charging
about which device needs to be used.
charging flap and
connector - risk of electrocution and/or fire!
disconnecting the
7
Contact any authorized Toyota retailer or
charging cable.
Toyota authorized repairer, or any reliable
Fixed blue
Deferred charging.
repairer.
Flashing green
Charging.
Charging cables, sockets
Fixed green
Charging complete.
The charging
and chargers
indicator lamp goes
The charging cable supplied with the vehicle
off after about 2
(depending on version) is compatible with the
minutes as the
electrical systems in the country of sale. When
vehicle's functions go
travelling abroad, check the compatibility of local
into standby.
electrical systems with the charging cable.
The meaning of each identification label is as
The indicator lamp
A full range of charging cables is available from
follows:
comes back on
your dealer.
when the vehicle is
Contact any authorized Toyota retailer or Toyota
unlocked using the
authorized repairer, or any reliable repairer for
Keyless Entry and
more information and to obtain suitable charging
Starting or when
cables.
a door is opened,
to indicate that
the battery is fully
charged.
Fixed red
Malfunction.
198
Identification label
Location
Configuration
Power type/Voltage range
Charging connector (vehicle side)
TYPE 2
AC
C
< 480 Vrms
Charging socket (charger side)
TYPE 2
AC
C
< 480 Vrms
Charging connector (vehicle side)
COMBO 2 (FF)
DC
K
50 V - 500 V
Standard charging, mode 2
Specific domestic charging cable - mode 2
Control unit (mode 2)
(AC)
Domestic socket
(domestic charging - alternating current (AC))
Mode 2 with a standard socket: 8 A maximum
charging current.
Identification label C on the charging
connector (vehicle side).
POWER
WARNING
Green: electrical connection established;
charging can begin.
Mode 2 with a Green'Up socket: 16 A
Specific domestic charging cable (mode 2)
CHARGE
maximum charging current.
You must not damage the cable.
Flashing green: charging in progress or
To have this type of socket installed, call a
In the event of damage, do not use it and
temperature pre-conditioning activated.
professional installer.
contact any authorized Toyota retailer or
Fixed green: charging complete.
Toyota authorized repairer, or any reliable
FAULT
repairer to replace it.
199
Red: fault; charging not permitted or must be
2.
Always use a correctly earthed power
13. Never plug the cable into the wall socket (or
stopped immediately. Check that everything
socket, protected by a 30 mA residual
unplug it) with wet hands.
is connected correctly and that the electrical
current device.
14. Do not force the connector if it is locked into
system is not faulty.
3.
Always use an electrical socket protected
the vehicle.
If the indicator lamp does not go off, contact any
by a circuit-breaker appropriate for the
authorized Toyota retailer or Toyota authorized
Control unit label - State of indicator
electrical circuit’s current rating.
repairer, or any reliable repairer.
lamps
7
4.
The weight of the control unit must not be
Upon plugging the charging cable into a
borne by the electrical socket, plug and
State of the
domestic socket, all of the indicator lamps come
cables.
indicator lamp
on briefly.
5.
Never use this charging cable if it is
If no indicator lamps come on, check the
Off
defective or in any way damaged.
domestic socket's circuit-breaker:
6.
Never attempt to repair or open this
- If the circuit-breaker has tripped, contact a
charging cable. It contains no repairable
professional to check that the electrical system
On
parts - replace the charging cable if it is
is compatible and/or carry out any necessary
damaged.
repairs.
7.
Never immerse this charging cable in water.
- If the circuit-breaker has not tripped, stop
Flashing
8.
Never use this charging cable with an
using the charging cable and contact any
extension cable, a multi-plug socket, a
authorized Toyota retailer or Toyota authorized
conversion adaptor or on a damaged
repairer, or any reliable repairer.
electrical socket.
Control unit label - Recommendations
9.
Do not unplug the plug from the wall as a
means of stopping charging.
Refer to the handbook before use.
10.
Immediately stop charging, by locking and
then unlocking the vehicle using the remote
control key, if the charging cable or wall
socket feel burning hot to the touch.
11.
This charging cable includes components
liable to cause electrical arcing or sparks.
1. Incorrect use of this charging cable may
Do not expose to flammable vapours.
result in fire, property damage and serious
12.
Only use this charging cable with TOYOTA
injury or death by electrocution!
vehicles.
Большое спасибо!
Ваше мнение очень важно для нас.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст