Toyota Camry Hybrid (2022 year). Manual in english — page 6
94
2. Instrument cluster
4.2-inch display
7-inch display
The units used on the meters and some indicators may differ depending on
the target region.
Warning lights and indicators
The warning lights and indicators on the instrument cluster, cen-
ter panel and outside rear view mirrors inform the driver of the
status of the vehicle’s various systems.
For the purpose of explanation, the following illustrations dis-
play all warning lights and indicators illuminated.
95
2. Instrument cluster
2
Instrument cluster
Warning lights inform the driver of malfunctions in any of the vehicle’s
systems.
Warning lights
*
1
(U.S.A.)
Brake system warning
light (
*
2
Inappropriate pedal
operation warning light
(
*
1
(Canada)
(Red)
Brake system warning
light (
(U.S.A.)
Parking brake indicator
(
*
1
(Yellow)
Brake system warning
light (
(Canada)
Parking brake indicator
(
*
1
(U.S.A.)
Malfunction indicator
lamp (
*
1, 3
Brake hold operated
indicator (
*
1
(Canada)
Malfunction indicator
lamp (
*
1
(Red/yellow)
Electric power steering
system warning light
(
*
1
SRS warning light
(
(Yellow)
LTA indicator (
*
1
(U.S.A.)
ABS warning light
(
*
1
(Flashes or
illuminates)
PCS warning light
(
*
1
(Canada)
ABS warning light
(
*
1, 3
(If equipped)
PKSB OFF indicator
(
96
2. Instrument cluster
*
1
: These lights turn on when the power switch is turned to ON mode to indi-
cate that a system check is being performed. They will turn off after the
hybrid system is on, or after a few seconds. There may be a malfunction in
a system if a light does not come on, or turn off. Have the vehicle
inspected by your Toyota dealer.
*
2
: This light illuminates on the multi-information display with a message.
*
3
: This light flashes to indicate a malfunction.
*
4
: This light illuminates on the center panel.
(If equipped)
Intuitive parking assist
OFF indicator (
Driver’s and front
passenger’s seat belt
reminder light
(
(If equipped)
RCD OFF indicator
(
*
4
Rear passengers’ seat
belt reminder lights
(
*
1
Slip indicator (
*
1
Master warning light
(
Low fuel level warning
light (
*
1
Tire pressure warning
light (
97
2. Instrument cluster
2
Instrument cluster
The indicators inform the driver of the operating state of the vehicle’s
various systems.
Indicators
Turn signal indicator
(
Dynamic radar cruise
control indicator
(
(U.S.A.)
Headlight indicator
(
Cruise control “SET”
indicator
(
(Canada)
Tail light indicator
(
*
1, 2
PCS warning light
(
Headlight high beam
indicator (
*
1, 2
(If equipped)
PKSB OFF indicator
(
*
1
Automatic High Beam
indicator (
(White)
LTA indicator (
AGC (Auto Glide Con-
trol) indicator (
(Green)
LTA indicator
(
(U.S.A.)
Parking brake indicator
(
*
3
(Yellow)
LTA indicator (
(Canada)
Parking brake indicator
(
*
1, 3
Slip indicator (
*
1
Brake hold operated
indicator (
*
1, 2
VSC OFF indicator
(
*
1
Brake hold standby
indicator (
(If equipped)
“BSM” indicator
(
Cruise control indicator
(
(If equipped)
“RCTA” indicator
(
98
2. Instrument cluster
*
1
: These lights turn on when the power switch is turned to ON mode to indi-
cate that a system check is being performed. They will turn off after the
hybrid system is on, or after a few seconds. There may be a malfunction in
a system if a light does not come on, or turn off. Have the vehicle
inspected by your Toyota dealer.
*
2
: This light turns on when the system is off.
*
3
: This light flashes to indicate that the system is operating.
*
4, 5
(If equipped)
BSM (Blind Spot Moni-
tor) outside rear view
mirror indicators
(
“READY” indicator
(
*
1, 6
“AIRBAG ON/OFF”
indicator (
EV indicator (
*
6
Security indicator
(
EV drive mode indicator
(
(If equipped)
Intuitive parking assist
OFF indicator (
*
7
Low outside tempera-
ture indicator (
“SPORT” indicator
(
(If equipped)
RCD OFF indicator
(
“ECO MODE” indicator
(
99
2. Instrument cluster
2
Instrument cluster
*
4
: These indicators will illuminate in the following situations to indicate that
the system initial check is being performed:
• When the BSM function or RCTA function is enabled and the power
switch is turned to ON mode.
• When the power switch is ON mode and the BSM function is enabled.
• When the power switch is ON mode and the RCTA function is enabled.
(At this time, a buzzer will also sound).
The indicators will turn off after a few seconds. If the indicators do not
illuminate or turn off, or if a buzzer does not sound when the RCTA func-
tion is enabled, the system may be malfunctioning. Have the vehicle
inspected by your Toyota dealer.
*
5
: This light illuminates on the outside rear view mirrors.
*
6
: This light illuminates on the center panel.
*
7
: When the outside temperature is approximately 37°F (3°C) or lower, this
indicator will flash for approximately 10 seconds, then stay on.
WARNING
■
If a safety system warning light does not come on
Should a safety system light such as the ABS and SRS warning lights not
come on when you start the hybrid system, this could mean that these sys-
tems are not available to help protect you in an accident, which could result
in death or serious injury. Have the vehicle inspected by your Toyota dealer
immediately if this occurs.
100
2. Instrument cluster
4.2-inch display
7-inch display
Gauges and meters
101
2. Instrument cluster
2
Instrument cluster
Hybrid System Indicator
Displays hybrid system output or regeneration level (
Shift position (
Outside temperature
Displays the outside temperature within the range of -40°F (-40°C) to
122°F (50°C). Low outside temperature indicator comes on when the
ambient temperature is 37°F (3°C) or lower.
Multi-information display
Presents the driver with a variety of vehicle data (
Displays warning messages in case of a malfunction (
Speedometer
Fuel gauge
Displays the fuel level. In the following situations, the actual fuel level may
not be displayed correctly:
• After refueling only a small amount (approximately 5 L or less)
• When stopped on a hill or other slope
• When driving on a slope or around a curve
Odometer and trip meter (
Engine coolant temperature gauge
Displays the engine coolant temperature
The brightness of the instrument panel lights can be adjusted.
Darker
Brighter
• The brightness of the instrument
panel lights can be adjusted
individually for day mode and
night mode
*
.
• If the brightness is adjusted
when the surroundings are
bright and the tail lights are on
(day mode brightness adjust-
ment), the brightness level of
night mode will be adjusted at
the same time.
*
: Day mode and night mode:
Instrument panel light control
1
2
3
4
5
6
7
8
1
2
102
2. Instrument cluster
■
The meters and display illuminate when
The power switch is in ON mode.
■
Brightness of the meters (day mode and night mode)
●
The brightness of the meters is changed between day mode and night
mode.
• Day mode: When the tail lights are off or when the tail lights are on but
the surrounding area is bright
• Night mode: When the tail lights are on and the surrounding area is dark
●
When in night mode, the brightness will be reduced slightly unless the
meters are set to the maximum brightness level.
■
Hybrid System Indicator
●
By keeping the indicator needle within Eco area, more Eco-friendly driving
can be achieved.
●
Charge area indicates “regeneration”
*
status. Regenerated energy will be
used to charge the battery.
*
: When used in this manual, “regeneration” refers to the conversion of
energy created by the movement of the vehicle into electrical energy.
The Hybrid System Indicator will not operate in the following situations:
●
The “READY” indicator is not illuminated.
●
The shift lever is in P, R or N position.
READY OFF area
Shows that the hybrid system is not
operating.
Charge area
Shows regenerative charging.
Hybrid Eco area
Shows that gasoline engine power is
not being used very often.
The gasoline engine will automatically
stop and restart under various condi-
tions.
Eco area
Shows that the vehicle is being driven in
an Eco-friendly manner.
Power area
Shows that an Eco-friendly driving
range is being exceeded (during full
power driving etc.)
1
2
3
4
5
103
2. Instrument cluster
2
Instrument cluster
■
Engine speed
On hybrid vehicles, engine speed is precisely controlled in order to help
improve fuel efficiency and reduce exhaust emissions etc.
There are times when the engine speed that is displayed may differ even
when vehicle operation and driving conditions are the same.
■
Outside temperature display
In the following situations, the correct outside temperature may not be dis-
played, or the display may take longer than normal to change:
●
When stopped, or driving at low speeds (less than 16 mph [25 km/h])
●
When the outside temperature has changed suddenly (at the entrance/exit
of a garage, tunnel, etc.)
●
When “
” or “E” is displayed, the system may be malfunctioning.
Take your vehicle to your Toyota dealer.
■
Fuel gauge and driving range display
The fuel gauge and driving range display are linked. If the fuel gauge and
driving range display do not update after refueling a small amount, they can
be updated by performing the following procedure:
Stop the vehicle on a level surface.
Wait until the fuel in the fuel tank stabilizes.
Press the ODO/TRIP switch to change the odometer and trip meter display
to the odometer.
Turn the power switch off.
While pressing and holding the ODO/TRIP switch, turn the power switch to
ON mode.
Continue holding the ODO/TRIP switch for approximately 5 seconds.
Release the switch when the odometer begins blinking.
Updating will be complete when the odometer blinks for approximately 5
seconds and then returns to the normal display.
NOTICE
■
To prevent damage to the engine and its components
The engine may be overheating if the engine coolant temperature gauge is
in the red zone (H). In this case, immediately stop the vehicle in a safe
place, and check the engine after it has cooled completely. (
1
2
3
4
5
104
2. Instrument cluster
The multi-information display presents the driver with a variety of driv-
ing-related data, such as the current outside temperature. The multi-
information display can also be used to change the display settings
and other settings.
Shift position (
Menu icon display area
Displays the following items.
When a menu icon is not selected, the outside temperature and clock are
displayed.
• Menu icons (
• Outside temperature (
• Clock
*
*
: For clock settings, refer to “NAVIGATION AND MULTIMEDIA SYSTEM
OWNER’S MANUAL”.
Content display area
A variety of information can be displayed by selecting a menu icon. Addi-
tionally, warning or suggestion/advice pop-up displays will be displayed in
some situations.
• Menu icon content (
• Suggestion function (
• Warning message (
Odometer/trip meter (
Indicators (
Multi-information display (4.2-inch display)
Summary of functions
1
2
3
4
5
105
2. Instrument cluster
2
Instrument cluster
RSA (Road Sign Assist) (if equipped) (
“ODO/TRIP” switch (
Meter control switches (
◆
Using the content display area
The content display area is operated using the meter control
switches.
Scroll screens
*
, change the
displayed content
*
and move
the cursor
Press: Enter/Set
Press and hold: Reset
Return to the previous
screen
Pressing and holding the switch
will display the first screen of the
selected menu icon.
Call sending/receiving and history display
Linked with the hands-free system, sending or receiving call is dis-
played. For details regarding the hands-free system, refer to “NAVIGA-
TION AND MULTIMEDIA SYSTEM OWNER’S MANUAL”.
*
: When the screen can be scrolled or different content can be displayed,
a mark, such as an arrow, will be displayed to suggest which switch to
operate.
◆
Using the odometer/trip meter
Items in this area are operated using the “ODO/TRIP” switch.
Press: Change displayed item
Each time the switch is pressed,
the displayed item will be
changed.
Press and hold: Reset
Display the desired trip meter
and press and hold the switch to
reset the trip meter.
Using the multi-information display
6
7
8
1
2
3
4
106
2. Instrument cluster
Select a menu icon to display its content.
Drive information (
Select to display various drive data.
Audio system-linked display
Select to enable selection of an audio source or track on the meter
using the meter control switches.
Driving assist system information
Select to display the operational status of the following systems:
• Dynamic radar cruise control with full-speed range (
• LTA (Lane Tracing Assist) (
• RSA (Road Sign Assist) (if equipped) (
Warning message display (
Select to display warning messages and measures to be taken if a mal-
function is detected.
Settings display (
Select to change the meter display settings and other settings.
Menu icons
107
2. Instrument cluster
2
Instrument cluster
■
Trip (after start)
Average fuel economy
*
Displays the average fuel con-
sumption since hybrid system
start.
Average vehicle speed
Displays the average vehicle
speed since hybrid system start.
Elapsed time
Displays the time elapsed since
hybrid system start.
*
: Use the displayed fuel consumption as a reference only.
■
Total (after reset)
Current fuel consumption
Displays the instantaneous cur-
rent fuel consumption.
Average fuel economy
*
1, 2
Displays the average fuel con-
sumption since the display was
reset.
Average
vehicle
speed/
Elapsed time
*
1
Displays the average vehicle speed since reset or elapsed time since
reset, as selected in
. (
*
1
: Pressing and holding
will reset the average fuel consumption and
average vehicle speed/elapsed time.
*
2
: Use the displayed fuel consumption as a reference only.
Drive information (
)
1
2
3
1
2
3
108
2. Instrument cluster
■
Tank (after refuel)
Driving range
*
1, 2
Displays the driving range with
remaining fuel.
Average fuel economy
*
1, 3
Displays the average fuel con-
sumption since the vehicle was
refueled.
*
1
: When only a small amount of fuel is added to the tank, the display may
not be updated.
When refueling, turn the power switch off. If the vehicle is refueled with-
out turning the power switch off, the display may not be updated.
*
2
: This distance is computed based on your average fuel consumption. As
a result, the actual distance that can be driven may differ from that dis-
played.
*
3
: Use the displayed fuel consumption as a reference only.
■
Energy monitor
■
Speedometer
Displays the vehicle speed.
■
Tire pressure (vehicles with a tire inflation pressure display
function)
■
Blank (No items)
Displays no drive information contents.
1
2
109
2. Instrument cluster
2
Instrument cluster
◆
Changing settings
Use the meter control switches on the steering wheel to change
settings.
Press
or
to select
.
Operate the switches to select a desired item.
Change the setting by referring to the message displayed on the
screen.
◆
Setting items
■
LTA (Lane Tracing Assist) (
The following LTA system settings can be changed:
Settings display (
)
1
2
3
Item
Settings
Details
Lane center
On
Select to enable/disable the lane
centering function.
Off
Alert sensitivity
High
Select to set the warning sensi-
tivity.
Std.
Sway warning
On
Select to enable/disable the vehi-
cle sway warning.
Off
Sway sensitivity
High
Select to set the vehicle sway
warning sensitivity.
Std.
Low
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст