Toyota Tundra (2015 year). Manual — part 860
(d) Using needle-nose pliers, remove the 4 snap rings from the
grooves.
(f) Clamp the shaft in a vise between aluminum plates.
(g) Using SST, pull out the universal joint spider bearing from the
shaft.
SST: 09331-60010
SST: 09950-40011
09951-04010
09952-04010
09953-04020
09954-04010
09957-04010
09958-04011
SST: 09955-04100
Text in Illustration
*a
Spider Bearing
*b
Turn
*c
Hold
NOTICE:
Pull out the spider bearing until the SST claws contact the shaft's
universal joint yoke.
(h) Clamp the protruding universal joint spider bearing in a vise.
PROPELLER SHAFT: PROPELLER SHAFT ASSEMBLY (for 4WD):...
(i) Using a brass bar and hammer, tap the shaft yoke to remove the
universal joint spider bearing.
Text in Illustration
*a
Hammering Point
NOTICE:
Do not tap the shaft tube.
HINT:
Use the same removal procedure for the universal joint spider
bearing on the opposite side.
(j) Using SST, pull out the universal joint spider bearing from the
flange yoke.
SST: 09331-60010
SST: 09950-40011
09951-04010
09952-04010
09953-04020
09954-04010
09957-04010
09958-04011
SST: 09955-04100
Text in Illustration
*a
Spider Bearing
*b
Turn
*c
Hold
NOTICE:
Pull out the spider bearing until the SST claws contact the flange
yoke.
(k) Clamp the protruding universal joint spider bearing in a vise.
PROPELLER SHAFT: PROPELLER SHAFT ASSEMBLY (for 4WD):...
(l) Using a brass bar and hammer, tap the flange yoke to remove
the universal joint spider bearing.
Text in Illustration
*a
Hammering Point
HINT:
Use the same removal procedure for the universal joint spider
bearing on the opposite side.
(m) Remove the spider from the flange yoke.
PROPELLER SHAFT: PROPELLER SHAFT ASSEMBLY (for 4WD):...
Last Modified: 9-16-2014
6.6 G
Doc ID: RM000002HBO00LX
Model Year: 2015
Model: Tundra
Prod Date Range: [08/2014 - ]
Title: PROPELLER SHAFT: PROPELLER SHAFT ASSEMBLY (for 4WD): INSPECTION; 2015 MY Tundra [08/2014 -
]
INSPECTION
1. INSPECT PROPELLER SHAFT WITH CENTER BEARING ASSEMBLY
(a) Using a dial indicator, measure the intermediate shaft runout.
Maximum runout:
0.61 mm (0.0240 in.)
If the intermediate shaft runout is more than the maximum, replace the propeller shaft with center
bearing assembly.
(b) Using a dial indicator, measure the propeller shaft runout.
Maximum runout:
1.02 mm (0.0402 in.)
If the propeller shaft runout is more than the maximum,
replace the propeller shaft with center bearing assembly.
2. INSPECT REAR PROPELLER SHAFT UNIVERSAL JOINT
SPIDER BEARING
(a) Mount the propeller shaft in a vise.
NOTICE:
Be careful not to grip the propeller shaft tube too tightly in a vise
as this will cause deformation.
(b) Inspect the spider bearing for wear or damage.
(c) Using a dial indicator, measure the spider bearing axial play by
0.05 mm (0.00197 in.)
If the spider bearing axial play is more than the maximum,
PROPELLER SHAFT: PROPELLER SHAFT ASSEMBLY (for 4WD):...
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст