Toyota Tundra (2015 year). Manual — part 1371
(a) Install 5 new gaskets to the camshaft bearing caps. (No. 1, No.
3).
(b) Install the cover gasket to the cylinder head cover.
NOTICE:
Remove any oil from the contact surface.
(c) Apply seal packing as shown in the illustration.
Seal packing:
Toyota Genuine Seal Packing Black, Three Bond 1207B or
equivalent
NOTICE:
Remove any oil from the contact surface.
Install the cylinder head cover within 3 minutes and tighten the
bolts within 15 minutes after applying seal packing.
(d) Install the cylinder head cover washer with a new seal and the
14 bolts.
Torque:
for bolt A -
21 N·m {214 kgf·cm, 15ft·lbf}
except bolt A -
12 N·m {122 kgf·cm, 9ft·lbf}
NOTICE:
Do not start the engine for at least 2 hours after the installation.
46. INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY LH
(a) Install 5 new gaskets to the camshaft bearing caps (No. 2, No.
3).
(b) Install the cover gasket to the cylinder head cover.
NOTICE:
1UR-FE ENGINE MECHANICAL: ENGINE UNIT: REASSEMBLY; 2...
Remove any oil from the contact surface.
(c) Apply seal packing as shown in the illustration.
Seal packing:
Toyota Genuine Seal Packing Black, Three Bond 1207B or
equivalent
NOTICE:
Remove any oil from the contact surface.
Install the cylinder head cover within 3 minutes and tighten the
bolts within 15 minutes after applying seal packing.
(d) Install the cylinder head cover washer with a new seal and the
14 bolts.
Torque:
for bolt A -
21 N·m {214 kgf·cm, 15ft·lbf}
except bolt A -
12 N·m {122 kgf·cm, 9ft·lbf}
NOTICE:
Do not start the engine for at least 2 hours after the installation.
47. INSTALL CAMSHAFT OIL CONTROL VALVE ASSEMBLY
(a) LH:
(3) Install the 2 oil control valves with the 2 bolts.
Torque:
10 N·m {102 kgf·cm, 7ft·lbf}
(b) RH:
(3) Install the 2 oil control valves with the 2 bolts.
Torque:
10 N·m {102 kgf·cm, 7ft·lbf}
1UR-FE ENGINE MECHANICAL: ENGINE UNIT: REASSEMBLY; 2...
48. INSTALL CRANKSHAFT POSITION SENSOR
(a) Install the crankshaft position sensor with the bolt.
Torque:
10 N·m {102 kgf·cm, 7ft·lbf}
49. INSTALL CRANKSHAFT POSITION SENSOR
PROTECTOR
(a) Install the sensor protector with the 2 bolts.
Torque:
10 N·m {102 kgf·cm, 7ft·lbf}
50. INSTALL CAMSHAFT POSITION SENSOR
(a) Install the camshaft position sensor with the bolt.
Torque:
10 N·m {102 kgf·cm, 7ft·lbf}
51. INSTALL VVT SENSOR
(a) LH:
(1) Install the 2 VVT sensors with the 2 bolts.
Torque:
10 N·m {102 kgf·cm, 7ft·lbf}
(b) RH:
(1) Install the 2 VVT sensors with the 2 bolts.
Torque:
10 N·m {102 kgf·cm, 7ft·lbf}
1UR-FE ENGINE MECHANICAL: ENGINE UNIT: REASSEMBLY; 2...
52. INSTALL SPARK PLUG
(a) Using a 16 mm plug wrench, install the 8 spark plugs.
Torque:
21 N·m {214 kgf·cm, 15ft·lbf}
53. INSTALL OIL FILLER CAP HOUSING
(b) Install the cap housing with the 2 bolts.
Torque:
10 N·m {102 kgf·cm, 7ft·lbf}
54. INSTALL OIL FILLER CAP SUB-ASSEMBLY
55. INSTALL CRANKSHAFT PULLEY
56. INSTALL OIL FILTER BRACKET
57. INSTALL OIL FILTER ELEMENT
1UR-FE ENGINE MECHANICAL: ENGINE UNIT: REASSEMBLY; 2...
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст