Toyota Tundra (2015 year). Manual — part 1372
Last Modified: 9-16-2014
6.6 A
Doc ID: RM0000030XK02BX
Model Year: 2015
Model: Tundra
Prod Date Range: [08/2014 - ]
Title: 1UR-FE ENGINE MECHANICAL: ENGINE UNIT: INSTALLATION; 2015 MY Tundra [08/2014 - ]
INSTALLATION
1. INSTALL NOISE FILTER
(a) RH Side:
Install the noise filter to the cylinder head cover with the bolt.
Torque:
10 N·m {102 kgf·cm, 7ft·lbf}
(b) LH Side:
Install the noise filter to the cylinder head cover with the bolt.
Torque:
10 N·m {102 kgf·cm, 7ft·lbf}
2. INSTALL IGNITION COIL ASSEMBLY
(a) Install the 8 ignition coils with the 8 bolts.
Torque:
10 N·m {102 kgf·cm, 7ft·lbf}
3. INSTALL KNOCK SENSOR
4. INSTALL NO. 11 WATER BY-PASS HOSE
(a) Install the No. 11 water by-pass hose.
HINT:
(a) Connect the 3 clamps and 4 knock sensor connectors to install
the engine wire.
6. INSTALL NO. 1 ENGINE COVER
1UR-FE ENGINE MECHANICAL: ENGINE UNIT: INSTALLATION;...
(a) Install the No. 1 engine cover.
7. INSTALL NO. 2 ENGINE COVER
(a) Install the No. 2 engine cover.
8. INSTALL SEPARATOR CASE
9. INSTALL NO. 1 IDLER PULLEY SUB-ASSEMBLY
10. INSTALL WATER PUMP PULLEY
11. INSTALL FRONT WATER BY-PASS JOINT
12. INSTALL WATER INLET HOUSING
13. INSTALL WATER BY-PASS PIPE SUB-ASSEMBLY
14. INSTALL AIR TUBE SUB-ASSEMBLY RH
15. INSTALL NO. 1 WATER BY-PASS HOSE
16. INSTALL NO. 3 ENGINE COVER
17. INSTALL NO. 4 ENGINE COVER
18. INSTALL OIL PRESSURE SENDER GAUGE ASSEMBLY
19. INSTALL FUEL DELIVERY PIPE SUB-ASSEMBLY RH
20. INSTALL FUEL DELIVERY PIPE SUB-ASSEMBLY LH
1UR-FE ENGINE MECHANICAL: ENGINE UNIT: INSTALLATION;...
21. INSTALL FRONT NO. 1 ENGINE MOUNTING BRACKET
LH
(a) Install the mounting bracket with the 4 bolts.
Torque:
35 N·m {357 kgf·cm, 26ft·lbf}
22. INSTALL FRONT NO. 1 ENGINE MOUNTING BRACKET
RH
(a) Install the mounting bracket with the 4 bolts.
Torque:
35 N·m {357 kgf·cm, 26ft·lbf}
23. INSTALL FRONT ENGINE MOUNTING INSULATOR RH
(a) Install the mounting insulator with the nut.
Torque:
72 N·m {734 kgf·cm, 53ft·lbf}
24. INSTALL FRONT ENGINE MOUNTING INSULATOR LH
(a) Install the mounting insulator with the nut.
Torque:
72 N·m {734 kgf·cm, 53ft·lbf}
25. INSTALL CYLINDER BLOCK WATER DRAIN COCK SUB-ASSEMBLY
1UR-FE ENGINE MECHANICAL: ENGINE UNIT: INSTALLATION;...
Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent
(b) Install the water drain cocks.
Torque:
30 N·m {306 kgf·cm, 22ft·lbf}
(c) Tighten the drain cocks up to an additional 360° so that the drain cock pipes are within the range shown in
the illustration.
NOTICE:
Do not rotate the drain cocks more than 1 revolution (360°) after tightening the drain cocks to the
specified torque.
Do not loosen the drain cocks to adjust them. If an adjustment is necessary, remove the drain cocks and
reinstall them.
(d) Install the water drain cock plugs to the water drain cocks.
Torque:
13 N·m {130 kgf·cm, 9ft·lbf}
26. INSTALL EGR COOLER ASSEMBLY
27. CONNECT NO. 11 WATER BY-PASS HOSE
1UR-FE ENGINE MECHANICAL: ENGINE UNIT: INSTALLATION;...
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст