Toyota Tundra (2015 year). Manual — part 2184
A
OK
2.
CHECK MANUAL UP / DOWN FUNCTION
(a) Check that the manual UP/DOWN function using the master switch can operate the driver side power
window
.
OK:
Manual UP/DOWN function operates normally.
NG
GO TO FLOWCHART (DRIVER SIDE MOTOR
CIRCUIT)
3.
READ VALUE USING TECHSTREAM (MASTER SWITCH)
(a) Use the Data List to check if the master switch is functioning properly.
Master Switch
TESTER
DISPLAY
MEASUREMENT ITEM/RANGE
NORMAL CONDITION
DIAGNOSTIC
NOTE
D Door P/W
Auto SW
Driver side power window auto UP/ DOWN
switch signal / ON or OFF
ON: Driver side switch
operated
OFF: Driver side switch not
operated
-
OK:
The Techstream display changes normally when master switch is operated.
NG
REPLACE POWER WINDOW REGULATOR MASTER
SWITCH ASSEMBLY
OK
REPLACE FRONT POWER WINDOW REGULATOR
MOTOR ASSEMBLY LH
WINDSHIELD / WINDOWGLASS: POWER WINDOW CONTROL ...
Last Modified: 9-16-2014
6.6 J
Doc ID: RM000003F5900QX
Model Year: 2015
Model: Tundra
Prod Date Range: [08/2014 - ]
Title: WINDSHIELD / WINDOWGLASS: POWER WINDOW CONTROL SYSTEM (w/ Jam Protection Function): Front
Passenger Side Power Window Auto Up / Down Function does not Operate with Front Passenger Side Power
Window Switch; 2015 MY Tundra [08/2014 - ]
Front Passenger Side Power Window Auto Up / Down Function does not Operate with Front
Passenger Side Power Window Switch
DESCRIPTION
been initialized.
The power window regulator switch assembly has a malfunction.
The Hall-IC in the front passenger side motor has a malfunction.
The wiring between the power window regulator switch assembly and the front passenger side motor is
open or shorted.
WIRING DIAGRAM
INSPECTION PROCEDURE
NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
PROCEDURE
1.
CHECK FOR DTC
(a) Check for DTCs
.
Result
RESULT
PROCEED TO
DTC is not output
A
DTC B2311 is output
B
WINDSHIELD / WINDOWGLASS: POWER WINDOW CONTROL ...
A
OK
RESULT
PROCEED TO
DTC B2312 is output
C
DTC B2313 is output
D
LIN communication system DTCs are output
E
B
GO TO DTC (B2311)
C
GO TO DTC (B2312)
D
GO TO DTC (B2313)
E
GO TO LIN COMMUNICATION SYSTEM
2.
CHECK MANUAL UP / DOWN FUNCTION
(a) Check that the manual UP/DOWN function using the power window regulator switch assembly can
operate the front passenger side door power window
.
OK:
Manual UP/DOWN function operates normally.
NG
GO TO FLOWCHART (FRONT PASSENGER SIDE
MOTOR CIRCUIT)
3.
READ VALUE USING TECHSTREAM (FRONT PASSENGER SIDE MOTOR)
(a) Use the Data List to check if the front passenger side motor is functioning properly.
P-Door Motor
TESTER
DISPLAY
MEASUREMENT ITEM/RANGE
NORMAL CONDITION
DIAGNOSTIC
NOTE
P Door P/W
Auto SW
Front passenger side power window auto
UP/DOWN switch signal / ON or OFF
ON: Power window regulator
switch assembly operated
OFF: Power window regulator
-
WINDSHIELD / WINDOWGLASS: POWER WINDOW CONTROL ...
OK
TESTER
DISPLAY
MEASUREMENT ITEM/RANGE
NORMAL CONDITION
DIAGNOSTIC
NOTE
switch assembly not operated
OK:
The Techstream display changes when power window regulator switch assembly is operated.
NG
GO TO STEP 4
OK
REPLACE FRONT POWER WINDOW REGULATOR
MOTOR ASSEMBLY RH
4.
CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR SWITCH - FRONT
PASSENGER SIDE MOTOR)
(a) Disconnect the M10 switch connector.
(b) Disconnect the M11 motor connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
TESTER CONNECTION
CONDITION
SPECIFIED CONDITION
M10-8 (AUTO) - M11-4 (AUTO)
Always
Below 1 Ω
M10-8 (AUTO) - Body ground
Always
10 kΩ or higher
NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
WINDSHIELD / WINDOWGLASS: POWER WINDOW CONTROL ...
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст