Toyota Tundra (2015 year). Manual — part 2183
OK
TESTER CONNECTION
SWITCH CONDITION
SPECIFIED CONDITION
4 (U) - 3 (B)
UP
Below 1 Ω
1 (D) - 2 (SD)
UP
Below 1 Ω
4 (U) - 5 (SU)
OFF
Below 1 Ω
1 (D) - 2 (SD)
OFF
Below 1 Ω
4 (U) - 5 (SU)
DOWN
Below 1 Ω
1 (D) - 3 (B)
DOWN
Below 1 Ω
NG
REPLACE REAR POWER WINDOW REGULATOR
SWITCH ASSEMBLY RH
3.
CHECK HARNESS AND CONNECTOR (REAR SWITCH RH - REAR MOTOR RH)
(a) Disconnect the O5 switch connector.
(b) Disconnect the O3 motor connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
TESTER CONNECTION
CONDITION
SPECIFIED CONDITION
O5-1 (D) - O3-1
Always
Below 1 Ω
O5-4 (U) - O3-2
Always
Below 1 Ω
WINDSHIELD / WINDOWGLASS: POWER WINDOW CONTROL ...
OK
TESTER CONNECTION
CONDITION
SPECIFIED CONDITION
O5-1 (D) - Body ground
Always
10 kΩ or higher
O5-4 (U) - Body ground
Always
10 kΩ or higher
NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
4.
INSPECT REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH
(a) Remove the rear motor RH
.
(b) Apply battery voltage to connector terminals 1 and 2.
(c) Check that the motor gear rotates smoothly as follows.
OK:
MEASUREMENT CONDITION
SPECIFIED CONDITION
Battery positive (+) → 1
Battery negative (-) → 2
Motor gear rotates clockwise
Battery positive (+) → 2
Battery negative (-) → 1
Motor gear rotates counterclockwise
NG
REPLACE REAR POWER WINDOW REGULATOR
MOTOR ASSEMBLY RH
WINDSHIELD / WINDOWGLASS: POWER WINDOW CONTROL ...
OK
5.
CHECK HARNESS AND CONNECTOR (MASTER SWITCH - REAR SWITCH RH)
(a) Disconnect the N2 master switch connector.
(b) Disconnect the O5 switch connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
TESTER CONNECTION
CONDITION
SPECIFIED CONDITION
N2-10 (U) - O5-5 (SU)
Always
Below 1 Ω
N2-16 (D) - O5-2 (SD)
Always
Below 1 Ω
N2-10 (U) - Body ground
Always
10 kΩ or higher
N2-16 (D) - Body ground
Always
10 kΩ or higher
NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK
REPLACE POWER WINDOW REGULATOR MASTER
SWITCH ASSEMBLY
WINDSHIELD / WINDOWGLASS: POWER WINDOW CONTROL ...
Last Modified: 9-16-2014
6.6 J
Doc ID: RM000000Y46069X
Model Year: 2015
Model: Tundra
Prod Date Range: [08/2014 - ]
Title: WINDSHIELD / WINDOWGLASS: POWER WINDOW CONTROL SYSTEM (w/ Jam Protection Function):
Driver Side Power Window Auto Up / Down Function does not Operate with Power Window Master Switch; 2015
MY Tundra [08/2014 - ]
Driver Side Power Window Auto Up / Down Function does not Operate with Power Window Master
Switch
DESCRIPTION
The master switch has a malfunction.
The Hall-IC in the driver side motor has a malfunction.
The wiring between the master switch and the driver side motor is open or shorted.
INSPECTION PROCEDURE
PROCEDURE
1.
CHECK FOR DTC
(a) Check for DTCs
.
Result
RESULT
PROCEED TO
DTC is not output
A
DTC B2311 is output
B
DTC B2312 is output
C
DTC B2313 is output
D
LIN communication system DTCs are output
E
B
GO TO DTC (B2311)
C
GO TO DTC (B2312)
D
GO TO DTC (B2313)
E
GO TO LIN COMMUNICATION SYSTEM
WINDSHIELD / WINDOWGLASS: POWER WINDOW CONTROL ...
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст