Toyota Tundra (2015 year). Manual — part 2208
(a) Apply battery voltage to connector terminals 1 and 2.
(b) Check that the motor gear rotates smoothly as follows.
OK:
MEASUREMENT CONDITION
SPECIFIED CONDITION
Battery positive (+) → 1
Battery negative (-) → 2
Motor gear rotates counterclockwise
Battery positive (+) → 2
Battery negative (-) → 1
Motor gear rotates clockwise
If the result is not as specified, replace the rear power window regulator motor assembly RH.
Text in Illustration
*1
Motor Gear
*a
Component without harness connected
(Rear Power Window Regulator Motor Assembly RH)
*b
Clockwise
*c
Counterclockwise
4. INSPECT REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH (for CrewMax)
WINDSHIELD / WINDOWGLASS: POWER WINDOW REGULATO...
(a) Apply battery voltage to connector terminals 1 and 2.
(b) Check that the motor gear rotates smoothly as follows.
OK:
MEASUREMENT CONDITION
SPECIFIED CONDITION
Battery positive (+) → 1
Battery negative (-) → 2
Motor gear rotates clockwise
Battery positive (+) → 2
Battery negative (-) → 1
Motor gear rotates counterclockwise
If the result is not as specified, replace the rear power window regulator motor assembly RH.
Text in Illustration
*1
Motor Gear
*a
Component without harness connected
(Rear Power Window Regulator Motor Assembly RH)
*b
Clockwise
*c
Counterclockwise
WINDSHIELD / WINDOWGLASS: POWER WINDOW REGULATO...
Last Modified: 9-16-2014
6.6 A
Doc ID: RM0000030LJ00BX
Model Year: 2015
Model: Tundra
Prod Date Range: [08/2014 - ]
Title: WINDSHIELD / WINDOWGLASS: POWER WINDOW REGULATOR MOTOR (for Rear Door): INSTALLATION;
2015 MY Tundra [08/2014 - ]
INSTALLATION
HINT:
Use the same procedure for the LH side and RH side.
The procedure listed below is for the LH side.
A bolt without a torque specification is shown in the standard bolt chart
.
1. INSTALL POWER WINDOW REGULATOR MOTOR ASSEMBLY LH
Torque:
5.4 N·m {55 kgf·cm, 48in·lbf}
HINT:
2. INSTALL REAR DOOR WINDOW REGULATOR SUB-ASSEMBLY LH
(a) for Double Cab:
Install the rear door window regulator sub-assembly LH
.
(b) for CrewMax:
Install the rear door window regulator sub-assembly LH
.
3. INSTALL REAR DOOR GLASS SUB-ASSEMBLY LH
(a) for Double Cab:
Install the rear door glass sub-assembly LH
.
(b) for CrewMax:
Install the rear door glass sub-assembly LH
.
4. INSTALL REAR DOOR REAR LOWER WINDOW FRAME SUB-ASSEMBLY LH
(a) for Double Cab:
Install the rear door rear lower window frame sub-assembly LH
.
(b) for CrewMax:
Install the rear door rear lower window frame sub-assembly LH
.
5. INSTALL REAR DOOR GLASS RUN LH
(a) for Double Cab:
Install the rear door glass run LH
.
WINDSHIELD / WINDOWGLASS: POWER WINDOW REGULATO...
(b) for CrewMax:
Install the rear door glass run LH
.
6. INSTALL REAR DOOR SERVICE HOLE COVER LH
(a) for Double Cab:
Install the rear door service hole cover LH
.
(b) for CrewMax:
Install the rear door service hole cover LH
.
7. INSTALL REAR NO. 2 DOOR TRIM BRACKET
(a) for Double Cab:
Install the rear No. 2 door trim bracket
.
(b) for CrewMax:
Install the rear No. 2 door trim bracket
.
8. INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY LH
(a) for Double Cab:
Install the rear door trim board sub-assembly LH
.
(b) for CrewMax:
Install the rear door trim board sub-assembly LH
.
9. INSTALL REAR DOOR FRAME GARNISH LH
(a) for Double Cab:
Install the rear door frame garnish LH
.
(b) for CrewMax:
Install the rear door frame garnish LH
.
10. INSTALL REAR UPPER DOOR ARMREST BASE PANEL LH
(a) for Double Cab:
Install the rear upper door armrest base panel LH
.
(b) for CrewMax:
Install the rear upper door armrest base panel LH
.
11. INSTALL REAR DOOR INSIDE HANDLE BEZEL PLUG LH
(a) for Double Cab:
Install the rear door inside handle bezel plug LH
.
(b) for CrewMax:
Install the rear door inside handle bezel plug LH
.
12. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected
.
WINDSHIELD / WINDOWGLASS: POWER WINDOW REGULATO...
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст