Toyota Tundra (2015 year). Manual — part 135
3. CLEAR FREEZE FRAME DATA
NOTICE:
Clearing the DTCs will also clear the Freeze Frame Data
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch to ON.
(c) Turn the blind spot monitor main switch assembly (warning canceling switch assembly) on.
(d) Turn the Techstream on.
(e) Clear the DTCs and Freeze Frame Data.
PARK ASSIST / MONITORING: BLIND SPOT MONITOR SYSTEM:...
Last Modified: 9-16-2014
6.6 U
Doc ID: RM000004RS501IX
Model Year: 2015
Model: Tundra
Prod Date Range: [08/2014 - ]
Title: PARK ASSIST / MONITORING: BLIND SPOT MONITOR SYSTEM: DATA LIST / ACTIVE TEST; 2015 MY
Tundra [08/2014 - ]
DATA LIST / ACTIVE TEST
1. DATA LIST
NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely
on these reference values when deciding whether a part is faulty or not.
HINT:
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch to ON.
(c) Turn the Techstream on.
(d) Enter the following menus: Body Electrical / Blind Spot Monitor Master or Blind Spot Monitor Slave / Data
List.
(e) Read the Data List according to the display on the Techstream.
Blind Spot Monitor Master
TESTER DISPLAY MEASUREMENT ITEM/RANGE
NORMAL CONDITION
DIAGNOSTIC NOTE
Main Switch
Blind spot monitor main
switch assembly (warning
canceling switch assembly) /
OFF or ON
ON: Blind spot monitor main
switch assembly (warning
canceling switch assembly) on
OFF: Blind spot monitor main
switch assembly (warning
canceling switch assembly) off
-
Warning
Indicator Turning
on (Master)
on / OFF or ON
OFF: The following conditions
are not met
Not during
initial check
Vehicle
detected in
warning area
Vehicle speed
16 km/h (10
mph) or more
Shift lever in
any position
except R
-
PARK ASSIST / MONITORING: BLIND SPOT MONITOR SYSTEM...
TESTER DISPLAY MEASUREMENT ITEM/RANGE
NORMAL CONDITION
DIAGNOSTIC NOTE
No DTC output
Warning
Indicator
Flashing (Master)
/ OFF or ON
OFF: The following conditions
are not met
Not during
initial check
Vehicle
detected in
warning area
Vehicle speed
16 km/h (10
mph) or more
Shift lever in
any position
except R
No DTC output
-
Main Switch
Indicator Status
blind spot monitor main
switch assembly (warning
canceling switch assembly) /
OFF or ON
OFF: Indicator not illuminated
ON: Indicator illuminated
-
Warning
Indicator Input
Circuit Voltage
Outer rear view mirror
indicator voltage / Min.: 0 V,
Max.: 25.5 V
Not illuminated: 0 V
Illuminated: 2.5 to 7.5 V
-
Warning
Indicator Input
Circuit Current
Outer rear view mirror
indicator current / Min.: 0
mA, Max.: 255 mA
Not illuminated: 0 mA
Illuminated: 5 to 100 mA
-
Right Turn SW
State (CAN)
(right turn signal light
switch) / ON or OFF
-
Left Turn SW
State (CAN)
(left turn signal light switch)
/ ON or OFF
-
Reverse
ON: Shift lever in R
OFF: Shift lever in any position
except R
-
Vehicle Speed
Vehicle speed signal / Min.:
0 km/h (0 mph), Max.: 326
km/h (203 mph)
Vehicle stopped: 0 km/h (0
mph)
-
PARK ASSIST / MONITORING: BLIND SPOT MONITOR SYSTEM...
TESTER DISPLAY MEASUREMENT ITEM/RANGE
NORMAL CONDITION
DIAGNOSTIC NOTE
Steering Angle
Steering sensor / Min.:
-3072°, Max.: 3070.5°
Left turn: Increases
Right turn: Decreases
-
Power Supply
Voltage
Power supply voltage / Min.:
0 V, Max.: 50 V
Always: 11 to 14 V
-
Indicator Light
Control State
Outer rear view mirror
indicator dimming state /
Dim OFF or Dim ON
Dim OFF: Indicator not dimmed
Dim ON: Indicator dimmed
-
HV Flag
Hybrid vehicle / OFF or ON
OFF: Non-hybrid vehicle
ON: Hybrid vehicle
-
VGRS Flag
VGRS installed / OFF or ON
OFF: VGRS not installed
ON: VGRS installed
-
Main SW
Inspection
Completeness
Flag
switch assembly (warning
canceling switch assembly) /
Incompl or Compl
Incompl: Inspection not
completed
Compl: Inspection completed
Changes to Compl when the
blind spot monitor main
switch assembly (warning
canceling switch assembly)
is changed from off to on
during Test Mode.
Beam Axis
Inspection
Completeness
Flag
Compl
Incompl: Inspection not
completed
Compl: Inspection completed
Changes to Compl when
Test Mode has been
entered.
Destination
Undefined Flag
Destination determination /
Unfixed or Fixed
Unfixed: Sensor destination
information not determined
Fixed: Sensor destination
information determined
according to CAN destination
information
-
Angle
Adjustment by
Auto Alignment
Angle adjusted using auto
alignment / Min.: Under
-12.8 deg, Max.: Over 12.7
deg
Angle adjusted using auto
alignment is displayed
When the adjusted angle is
12.7 degrees or more,
"Over 12.7" is displayed and
when it is -12.8 degrees or
less, "Under -12.8" is
displayed
Setting of
Warning
Indicator Current
(Dim OFF)
not dimmed / Min.: 0 mA,
Max.: 100 mA
Always: 0 to 100 mA
-
Setting of
Warning
Indicator Current
(Dim ON)
dimmed / Min.: 0 mA, Max.:
100 mA
Always: 0 to 100 mA
-
Mirror LED Duty
Ratio (Blinking)
blinking / Min.: 0%, Max.:
100%
Always: 50%
-
PARK ASSIST / MONITORING: BLIND SPOT MONITOR SYSTEM...
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст