Toyota Tundra (2015 year). Manual — part 2160
34. CLEAN VEHICLE BODY
(a) Using a scraper, remove the moulding and adhesive from the
vehicle body.
away excess adhesive as shown in the illustration.
HINT:
Leave as much adhesive on the vehicle body as possible.
NOTICE:
Be careful not to damage the vehicle body.
Even if all the adhesive has been removed, clean the vehicle
body.
35. REMOVE BACK DOOR GLASS CHANNEL
WINDSHIELD / WINDOWGLASS: BACK WINDOW GLASS (for Re...
Last Modified: 9-16-2014
6.6 G
Doc ID: RM0000042WL006X
Model Year: 2015
Model: Tundra
Prod Date Range: [08/2014 - ]
Title: WINDSHIELD / WINDOWGLASS: BACK WINDOW GLASS (for Regular Cab and Double Cab): INSPECTION;
2015 MY Tundra [08/2014 - ]
INSPECTION
1. INSPECT POWER WINDOW REGULATOR MOTOR
ASSEMBLY (for Power Slide Type)
(2) Check that the motor gear rotates smoothly as follows.
OK:
MEASUREMENT CONDITION
SPECIFIED CONDITION
Battery positive (+) → 2
Battery negative (-) → 1
Motor gear rotates clockwise
Battery positive (+) → 1
Battery negative (-) → 2
Motor gear rotates counterclockwise
If the result is not as specified, replace the regulator motor.
2. INSPECT NO. 1 BACK POWER WINDOW RELAY (except 3UR-FBE)
(a) Remove the power window relay from the engine room relay block.
(b) Measure the resistance according to the value(s) in the table
below.
Standard resistance:
TESTER
CONNECTION
CONDITION
SPECIFIED
CONDITION
3 - 4
When battery voltage is not
applied between terminals 1 and
2
Below 1 Ω
When battery voltage is applied
between terminals 1 and 2
10 kΩ or higher
3 - 5
When battery voltage is not
applied between terminals 1 and
2
10 kΩ or higher
When battery voltage is applied
between terminals 1 and 2
Below 1 Ω
If the result is not as specified, replace the relay.
WINDSHIELD / WINDOWGLASS: BACK WINDOW GLASS (for Re...
3. INSPECT NO. 2 BACK POWER WINDOW RELAY
(a) Remove the power window relay from the engine room relay block.
(b) Measure the resistance according to the value(s) in the table
below.
Standard resistance:
TESTER
CONNECTION
CONDITION
SPECIFIED
CONDITION
3 - 4
When battery voltage is not
applied between terminals 1 and
2
Below 1 Ω
When battery voltage is applied
between terminals 1 and 2
10 kΩ or higher
3 - 5
When battery voltage is not
applied between terminals 1 and
2
10 kΩ or higher
When battery voltage is applied
between terminals 1 and 2
Below 1 Ω
If the result is not as specified, replace the relay.
4. INSPECT NO. 3 BACK POWER WINDOW RELAY (for 3UR-FBE)
(a) Remove the power window relay from the engine room relay block.
(b) Measure the resistance according to the value(s) in the table
below.
Standard resistance:
TESTER
CONNECTION
CONDITION
SPECIFIED
CONDITION
3 - 4
When battery voltage is not
applied between terminals 1 and
2
Below 1 Ω
When battery voltage is applied
between terminals 1 and 2
10 kΩ or higher
3 - 5
When battery voltage is not
applied between terminals 1 and
2
10 kΩ or higher
When battery voltage is applied
between terminals 1 and 2
Below 1 Ω
If the result is not as specified, replace the relay.
WINDSHIELD / WINDOWGLASS: BACK WINDOW GLASS (for Re...
Last Modified: 9-16-2014
6.6 A
Doc ID: RM00000304G00OX
Model Year: 2015
Model: Tundra
Prod Date Range: [08/2014 - ]
Title: WINDSHIELD / WINDOWGLASS: BACK WINDOW GLASS (for Regular Cab and Double Cab):
INSTALLATION; 2015 MY Tundra [08/2014 - ]
INSTALLATION
1. INSTALL NO. 1 BACK WINDOW GLASS SPACER
(a) Install 2 new spacers onto the back window assembly as shown
in the illustration.
2. INSTALL NO. 2 BACK WINDOW GLASS SPACER
(a) Install 2 new spacers onto the back window assembly as shown
in the illustration.
3. INSTALL BACK WINDOW ASSEMBLY
Allow the primer to dry for 3 minutes or more.
Do not apply primer to the adhesive.
Throw away any leftover primer.
Do not apply too much primer.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст