Toyota Tundra (2015 year). Manual — part 2161
HINT:
If primer is applied to an area that is not specified, wipe off the primer with a non-residue solvent before it
dries.
NOTICE:
Allow the primer to dry for 3 minutes or more.
Throw away any leftover primer.
Do not apply too much primer.
(c) Apply adhesive to the back window.
Adhesive:
Toyota Genuine Windshield Glass Adhesive or equivalent
After cutting off the tip, use all adhesive within the time written in the table below.
WINDSHIELD / WINDOWGLASS: BACK WINDOW GLASS (for Re...
Usage time frame:
TEMPERATURE
USAGE TIME FRAME
35°C (95°F)
15 minutes
20°C (68°F)
1 hour 40 minutes
5°C (41°F)
8 hours
(2) Load the sealer gun with the cartridge.
(3) Apply adhesive to the back window as shown in the illustration.
Standard:
AREA
SPECIFIED CONDITION
WINDSHIELD / WINDOWGLASS: BACK WINDOW GLASS (for Re...
AREA
SPECIFIED CONDITION
a
12.0 mm (0.472 in.)
b
8.0 mm (0.315 in.)
(d) Using suction cups, position the glass so that the reference marks are aligned. Press it in gently along the
rim.
NOTICE:
Allow the primer coating to dry for 3 minutes or more.
Check that the clips are attached to the vehicle body correctly.
Check the clearance between the vehicle body and glass.
NOTICE:
Check that the spacers are attached to the vehicle body correctly.
(f) Using a scraper, remove any excess or protruding adhesive.
NOTICE:
Do not drive the vehicle within the time written in the table below.
Minimum time:
TEMPERATURE
MINIMUM TIME PRIOR TO DRIVING VEHICLE
35°C (95°F)
1 hour 30 minutes
20°C (68°F)
5 hours
5°C (41°F)
24 hours
4. CHECK FOR LEAK AND REPAIR
(a) Conduct a leak test after the adhesive has completely hardened.
(b) Seal any leaks with auto glass sealer.
WINDSHIELD / WINDOWGLASS: BACK WINDOW GLASS (for Re...
5. INSTALL UPPER OUTSIDE BACK WINDOW MOULDING
(for Slide Type, for Power Slide Type)
(a) Clean the back window surface.
(1) Using a heat light, heat the back window surface.
(2) Remove the double-sided tape from the back window.
(3) Wipe off any tape adhesive residue with cleaner.
(b) If reusing the moulding:
Clean the moulding.
(1) Using a heat light, heat the moulding.
(2) Remove the double-sided tape from the moulding.
(3) Wipe off any tape adhesive residue with cleaner.
(4) Apply new double-sided tape to the moulding, as shown in
the illustration.
(c) Install the moulding.
(1) Using a heat light, heat the back window and moulding.
(2) Remove the peeling paper.
(3) Attach the 3 clips to install the moulding.
6. INSTALL LOWER OUTSIDE BACK WINDOW MOULDING
(for Slide Type, for Power Slide Type)
(a) Clean the back window surface.
(1) Using a heat light, heat the back window surface.
(2) Remove the double-sided tape from the back window.
(3) Wipe off any tape adhesive residue with cleaner.
(b) If reusing the moulding:
Clean the moulding.
(1) Using a heat light, heat the moulding.
(2) Remove the double-sided tape from the moulding.
(3) Wipe off any tape adhesive residue with cleaner.
(4) Apply new double-sided tape to the moulding, as shown in
the illustration.
(c) Install the moulding.
(1) Using a heat light, heat the back window and moulding.
(2) Remove the peeling paper.
(3) Attach the 3 clips to install the moulding.
7. INSTALL REAR ROOF DRIP SIDE FINISH MOULDING LH
8. INSTALL REAR ROOF DRIP SIDE FINISH MOULDING RH
WINDSHIELD / WINDOWGLASS: BACK WINDOW GLASS (for Re...
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст