Toyota Tundra (2015 year). Manual — part 740
9. INSPECT FORWARD CLUTCH RETURN SPRING
SUB-ASSEMBLY
Standard free length:
29.65 mm (1.17 in.)
10. INSPECT DIRECT CLUTCH DISC
peeled off or discolored, or 3) grooves or printed numbers have
Before assembling new discs, soak them in ATF for at least 2
hours.
11. INSPECT REVERSE CLUTCH RETURN SPRING
SUB-ASSEMBLY
Standard free length:
21.24 mm (0.836 in.)
12. INSPECT DIRECT CLUTCH RETURN SPRING
SUB-ASSEMBLY
Standard free length:
19.46 mm (0.766 in.)
13. INSPECT NO. 3 BRAKE DISC
peeled off or discolored, or 3) grooves or printed numbers have
Before assembling new discs, soak them in ATF for at least 2
hours.
AB60F AUTOMATIC TRANSMISSION: AUTOMATIC TRANSMIS...
14. INSPECT NO. 3 BRAKE PISTON RETURN SPRING
SUB-ASSEMBLY
Standard free length:
15.72 mm (0.619 in.)
15. INSPECT FRONT PLANETARY GEAR ASSEMBLY
(a) Using a feeler gauge, measure the front planetary pinion gear thrust clearance.
Standard clearance:
0.2 to 0.6 mm (0.00787 to 0.0236 in.)
If the clearance is greater than the standard, replace the front planetary gear assembly.
Standard inside diameter:
61.005 to 61.030 mm (2.402 to 2.403 in.)
If the inside diameter is greater than the standard, replace
the front planetary gear.
16. INSPECT 1-WAY CLUTCH ASSEMBLY
(a) Install the 1-way clutch to the 1-way clutch inner race.
(b) Hold the 1-way clutch inner race and turn the 1-way clutch.
Check that the 1-way clutch turns freely counterclockwise and
locks when turned clockwise.
(c) Remove the 1-way clutch from the 1-way clutch inner race.
AB60F AUTOMATIC TRANSMISSION: AUTOMATIC TRANSMIS...
17. INSPECT NO. 1 BRAKE DISC
peeled off or discolored, or 3) grooves or printed numbers have
Before assembling new discs, soak them in ATF for at least 2
hours.
18. INSPECT BRAKE PISTON RETURN SPRING
SUB-ASSEMBLY
Standard free length:
17.05 mm (0.671 in.)
19. INSPECT NO. 2 BRAKE DISC
peeled off or discolored, or 3) grooves or printed numbers have
Before assembling new discs, soak them in ATF for at least 2
hours.
20. INSPECT NO. 2 BRAKE PISTON RETURN SPRING
SUB-ASSEMBLY
Standard free length:
22.66 mm (0.892 in.)
21. INSPECT CENTER PLANETARY GEAR ASSEMBLY
(a) Using a feeler gauge, measure the center planetary gear pinion
thrust clearance.
Standard clearance:
0.20 to 0.60 mm (0.00787 to 0.0236 in.)
If the clearance is greater than the standard, replace the
center planetary gear assembly.
AB60F AUTOMATIC TRANSMISSION: AUTOMATIC TRANSMIS...
22. INSPECT NO. 3 1-WAY CLUTCH ASSEMBLY
(a) Hold the rear planetary ring gear flange and turn the 1-way
clutch. Check that the 1-way clutch turns freely counterclockwise
and locks when turned clockwise.
23. INSPECT INTERMEDIATE SHAFT
(a) Using a dial indicator, check the intermediate shaft runout.
Standard runout:
0.03 mm (0.00118 in.)
If the runout is greater than the standard, replace the intermediate shaft with a new one.
Standard diameter:
A
19.963 to 19.976 mm (0.7859 to 0.7865 in.)
B, C
30.150 to 30.163 mm (1.187 to 1.188 in.)
D, E
36.404 to 36.420 mm (1.433 to 1.434 in.)
If the diameter is less than the standard, replace the
intermediate shaft with a new one.
24. INSPECT NO. 4 BRAKE DISC
AB60F AUTOMATIC TRANSMISSION: AUTOMATIC TRANSMIS...
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст