Toyota Tundra (2015 year). Manual — part 145
Last Modified: 9-16-2014
6.6 C
Doc ID: RM000004S3401KX
Model Year: 2015
Model: Tundra
Prod Date Range: [08/2014 - ]
Title: PARK ASSIST / MONITORING: BLIND SPOT MONITOR SYSTEM: C1ABB; Blind Spot Monitor Master Module
Beam Axis Inspection Incomplete; 2015 MY Tundra [08/2014 - ]
DTC
C1ABB
Blind Spot Monitor Master Module Beam Axis Inspection Incomplete
DESCRIPTION
This DTC is stored when a beam axis inspection has not been performed for the blind spot monitor sensor RH.
HINT:
DTC CODE
DTC DETECTION CONDITION
TROUBLE AREA
C1ABB
A beam axis inspection has not been performed.
Blind spot monitor sensor RH
INSPECTION PROCEDURE
PROCEDURE
1.
PROCEED TO TEST MODE (BLIND SPOT MONITOR BEAM AXIS INSPECTION)
(a) Change the blind spot monitor sensor RH to Test Mode using the Techstream.
HINT:
Refer to Blind Spot Monitor Beam Axis Inspection
.
NEXT
END
PARK ASSIST / MONITORING: BLIND SPOT MONITOR SYSTEM:...
Last Modified: 9-16-2014
6.6 C
Doc ID: RM000004S2W01KX
Model Year: 2015
Model: Tundra
Prod Date Range: [08/2014 - ]
Title: PARK ASSIST / MONITORING: BLIND SPOT MONITOR SYSTEM: C1ABC; Blind Spot Monitor Slave Module
Beam Axis Inspection Incomplete; 2015 MY Tundra [08/2014 - ]
DTC
C1ABC
Blind Spot Monitor Slave Module Beam Axis Inspection Incomplete
DESCRIPTION
This DTC is stored when a beam axis inspection has not been performed for the blind spot monitor sensor LH.
HINT:
DTC CODE
DTC DETECTION CONDITION
TROUBLE AREA
C1ABC
A beam axis inspection has not been performed.
Blind spot monitor sensor LH
INSPECTION PROCEDURE
PROCEDURE
1.
PROCEED TO TEST MODE (BLIND SPOT MONITOR BEAM AXIS INSPECTION)
(a) Change the blind spot monitor sensor LH to Test Mode using the Techstream.
HINT:
Refer to Blind Spot Monitor Beam Axis Inspection
.
NEXT
END
PARK ASSIST / MONITORING: BLIND SPOT MONITOR SYSTEM:...
Last Modified: 9-16-2014
6.6 C
Doc ID: RM000002ADP03YX
Model Year: 2015
Model: Tundra
Prod Date Range: [08/2014 - ]
Title: PARK ASSIST / MONITORING: BLIND SPOT MONITOR SYSTEM: C1ABD,C1ABE; Short to +B in Buzzer;
2015 MY Tundra [08/2014 - ]
DTC
C1ABD
Short to +B in Buzzer
DTC
C1ABE
Short to GND or Open in Buzzer
DESCRIPTION
DTC C1ABD is stored when the blind spot monitor sensor LH detects a +B short in rear cross traffic
alert buzzer (blind spot monitor buzzer) circuit.
DTC C1ABE is stored when the blind spot monitor sensor LH detects a ground short or open in rear
cross traffic alert buzzer (blind spot monitor buzzer) circuit.
DTC
CODE
DTC DETECTION CONDITION
TROUBLE AREA
C1ABD
canceling switch assembly) is on with ignition
switch ON.
The blind spot monitor sensor is not sending
voltage to the buzzer but the buzzer receives
voltage above a specified level for a specified
sensor LH
Rear cross traffic alert
buzzer (blind spot
monitor buzzer)
Harness or connector
C1ABE
canceling switch assembly) is on with ignition
switch ON.
The current flowing to the buzzer is below a
specified value when buzzer operation voltage is
being sent to the buzzer.
Blind spot monitor
sensor LH
Rear cross traffic alert
buzzer (blind spot
monitor buzzer)
Harness or connector
WIRING DIAGRAM
PARK ASSIST / MONITORING: BLIND SPOT MONITOR SYSTEM:...
INSPECTION PROCEDURE
NOTICE:
When checking for DTCs, make sure that the blind spot main switch assembly (warning canceling switch
assembly) is on.
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
PROCEDURE
1.
CHECK DTC
(a) Clear the DTCs
.
(b) Recheck for DTCs and check if the same DTC is output again
.
OK:
No DTCs are output.
NG
GO TO STEP 2
OK
USE SIMULATION METHOD TO CHECK
2.
CHECK HARNESS AND CONNECTOR (REAR CROSS TRAFFIC ALERT BUZZER - BATTERY
AND BLIND SPOT MONITOR SENSOR LH)
(a) Disconnect the P19 rear cross traffic alert buzzer (blind spot monitor buzzer) connector.
(b) Disconnect the S5 blind spot monitor sensor LH connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
TESTER CONNECTION
CONDITION
SPECIFIED CONDITION
P19-2 (BZN) - S5-3 (BUZ)
Always
Below 1 Ω
PARK ASSIST / MONITORING: BLIND SPOT MONITOR SYSTEM:...
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст