Toyota Tundra (2015 year). Manual — part 2435
A
(a) Disconnect the E11 sender gauge connector.
(b) Apply battery positive (+) voltage to the sender gauge
terminal through a test LED.
(c) Check that the LED does not illuminate when the engine is
stopped.
(d) Check that the LED flashes when the engine is running. The
LED flashes when engine is running.
LED does not illuminate when engine is stopped.
Result
RESULT
PROCEED
TO
LED operates correctly according to engine condition
A
LED does not operate correctly according to engine
condition (for 1UR-FE)
B
LED does not operate correctly according to engine
condition (for 3UR-FE)
C
LED does not operate correctly according to engine
condition (for 3UR-FBE)
D
B
REPLACE OIL PRESSURE SENDER GAUGE ASSEMBLY
C
REPLACE OIL PRESSURE SENDER GAUGE ASSEMBLY
D
REPLACE OIL PRESSURE SENDER GAUGE ASSEMBLY
4.
CHECK HARNESS AND CONNECTOR (COMBINATION METER - OIL PRESSURE
SENDER GAUGE)
METER: METER / GAUGE SYSTEM: Oil Pressure Gauge Malfunction;...
(a) Disconnect the J28 meter connector.
(b) Disconnect the E11 gauge connector.
(c) Measure the resistance according to the value(s) in the table
below.
Standard Resistance:
TESTER CONNECTION
CONDITION
SPECIFIED
CONDITION
J28-27 (S) - E11-1
Always
Below 1 Ω
J28-27 (S) or E11-1 - Body
ground
Always
10 kΩ or higher
NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK
REPLACE COMBINATION METER ASSEMBLY
METER: METER / GAUGE SYSTEM: Oil Pressure Gauge Malfunction;...
Last Modified: 9-16-2014
6.6 J
Doc ID: RM000002ZNF01SX
Model Year: 2015
Model: Tundra
Prod Date Range: [08/2014 - ]
Title: METER: METER / GAUGE SYSTEM: Voltage Meter Malfunction; 2015 MY Tundra [08/2014 - ]
Voltage Meter Malfunction
DESCRIPTION
INSPECTION PROCEDURE
PROCEDURE
1.
INSPECT FUSE (MET)
(a) Remove the MET fuse from the engine room relay block.
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
TESTER CONNECTION
CONDITION
SPECIFIED CONDITION
MET fuse
Always
Below 1 Ω
NG
REPLACE FUSE
METER: METER / GAUGE SYSTEM: Voltage Meter Malfunction; 201...
OK
OK
2.
PERFORM ACTIVE TEST USING TECHSTREAM (VOLTMETER)
(a) Operate the Techstream according to the display and select "Active Test"
.
Combination Meter:
TESTER DISPLAY
TEST
PART
CONTROL RANGE
DIAGNOSTIC NOTE
Volt Meter
Operation
Voltmeter
OFF, 0 V, 3 V, 6V , 9 V, 12 V, 15
V or 18 V
Perform the test with the vehicle stopped and
engine idling
OK:
Needle indication is normal.
NG
REPLACE COMBINATION METER ASSEMBLY
3.
CHECK HARNESS AND CONNECTOR (COMBINATION METER - BATTERY AND BODY
GROUND)
(a) Disconnect the J28 meter connector.
(b) Measure the resistance and voltage according to the
value(s) in the table below.
Standard Resistance:
TESTER CONNECTION
CONDITION
SPECIFIED CONDITION
J28-24 (ES) - Body ground
Always
Below 1 Ω
Standard Voltage:
TESTER CONNECTION
SWITCH
CONDITION
SPECIFIED
CONDITION
J28-2 (IG+) - Body
ground
Ignition switch ON
11 to 14 V
Ignition switch off
Below 1 V
METER: METER / GAUGE SYSTEM: Voltage Meter Malfunction; 201...
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст