Toyota Tundra (2015 year). Manual — part 146
OK
NEXT
TESTER CONNECTION
CONDITION
SPECIFIED CONDITION
P19-2 (BZN) - Body ground
Always
10 kΩ or higher
(d) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
TESTER CONNECTION
SWITCH CONDITION
SPECIFIED CONDITION
P19-1 (BZP) - Body ground
Ignition switch ON
11 to 14 V
P19-1 (BZP) - Body ground
Ignition switch off
Below 1 V
NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
3.
REPLACE BLIND SPOT MONITOR BUZZER (REAR CROSS TRAFFIC ALERT BUZZER)
(a) Replace the rear cross traffic alert buzzer (blind spot monitor buzzer) with a new or normally
functioning one.
for Regular Cab:
for Double Cab:
for CrewMax:
4.
CHECK DTC
(a) Clear the DTCs
.
(b) Recheck for DTCs and check if the same DTC is output again
.
OK:
No DTCs are output.
NG
REPLACE BLIND SPOT MONITOR SENSOR LH
OK
END (REAR CROSS TRAFFIC ALERT BUZZER
[BLIND SPOT MONITOR BUZZER] IS DEFECTIVE)
PARK ASSIST / MONITORING: BLIND SPOT MONITOR SYSTEM:...
NEXT
Last Modified: 9-16-2014
6.6 C
Doc ID: RM00000500401DX
Model Year: 2015
Model: Tundra
Prod Date Range: [08/2014 - ]
Title: PARK ASSIST / MONITORING: BLIND SPOT MONITOR SYSTEM: C1AC1; Master Module Horizontal Axis
Misalignment; 2015 MY Tundra [08/2014 - ]
DTC
C1AC1
Master Module Horizontal Axis Misalignment
DESCRIPTION
HINT:
If drum tester such as a speedometer tester, brake/speedometer combination tester or chassis
dynamometer is used with the blind spot monitor main switch assembly (warning canceling switch
assembly) on, the blind spot monitor system may store this DTC by mistake.
DTC
CODE
DTC DETECTION CONDITION
TROUBLE AREA
C1AC1
When the blind spot monitor sensor deviates 5 degrees or more from the
horizontal axis when the system is activated.
Blind spot monitor
sensor RH
INSPECTION PROCEDURE
NOTICE:
When checking for DTCs, make sure that the blind spot monitor main switch assembly (warning canceling
switch assembly) is on.
PROCEDURE
1.
CHECK INSTALLATION CONDITION
.
HINT:
Take the appropriate action in accordance with the result.
2.
PERFORM BEAM AXIS CONFIRMATION
(a) Install the rear bumper
.
(b) Perform Blind Spot Monitor Beam Axis Confirmation using the Techstream
.
PARK ASSIST / MONITORING: BLIND SPOT MONITOR SYSTEM:...
OK:
Blind Spot Monitor Beam Axis Confirmation performs normally.
NG
REPLACE BLIND SPOT MONITOR SENSOR RH
OK
END
PARK ASSIST / MONITORING: BLIND SPOT MONITOR SYSTEM:...
NEXT
Last Modified: 9-16-2014
6.6 C
Doc ID: RM00000500601DX
Model Year: 2015
Model: Tundra
Prod Date Range: [08/2014 - ]
Title: PARK ASSIST / MONITORING: BLIND SPOT MONITOR SYSTEM: C1AC2; Slave Module Horizontal Axis
Misalignment; 2015 MY Tundra [08/2014 - ]
DTC
C1AC2
Slave Module Horizontal Axis Misalignment
DESCRIPTION
HINT:
If drum tester such as a speedometer tester, brake/speedometer combination tester or chassis
dynamometer is used with the blind spot monitor main switch assembly (warning canceling switch
assembly) on, the blind spot monitor system may store this DTC by mistake.
DTC
CODE
DTC DETECTION CONDITION
TROUBLE AREA
C1AC2
When the blind spot monitor sensor deviates 5 degrees or more from the
horizontal axis when the system is activated.
Blind spot monitor
sensor LH
INSPECTION PROCEDURE
NOTICE:
When checking for DTCs, make sure that the blind spot monitor main switch assembly (warning canceling
switch assembly) is on.
PROCEDURE
1.
CHECK INSTALLATION CONDITION
.
HINT:
Take the appropriate action in accordance with the result.
2.
PERFORM BEAM AXIS CONFIRMATION
(a) Install the rear bumper
.
(b) Perform Blind Spot Monitor Beam Axis Confirmation using the Techstream
.
PARK ASSIST / MONITORING: BLIND SPOT MONITOR SYSTEM:...
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст