Toyota Tundra (2015 year). Manual — part 1717
Last Modified: 9-16-2014
6.6 K
Doc ID: RM000002S54024X
Model Year: 2015
Model: Tundra
Prod Date Range: [08/2014 - ]
Title: 3UR-FBE ENGINE MECHANICAL: CYLINDER HEAD GASKET (for Bank 2): COMPONENTS; 2015 MY
Tundra [08/2014 - ]
COMPONENTS
ILLUSTRATION
3UR-FBE ENGINE MECHANICAL: CYLINDER HEAD GASKET (fo...
Last Modified: 9-16-2014
6.6 A
Doc ID: RM000002S5504DX
Model Year: 2015
Model: Tundra
Prod Date Range: [08/2014 - ]
Title: 3UR-FBE ENGINE MECHANICAL: CYLINDER HEAD GASKET (for Bank 2): REMOVAL; 2015 MY Tundra
[08/2014 - ]
REMOVAL
1. REMOVE EXHAUST MANIFOLD SUB-ASSEMBLY RH
(a) Remove the exhaust manifold RH
.
2. REMOVE CAMSHAFTS (for Bank 2)
(a) Remove the camshafts
.
3. REMOVE NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY
(a) Remove the 16 valve rocker arms from the cylinder head.
HINT:
Arrange the removed parts in the correct order.
4. REMOVE VALVE LASH ADJUSTER ASSEMBLY
(a) Remove the 16 valve lash adjusters from the cylinder head.
HINT:
Arrange the removed parts in the correct order.
5. REMOVE VALVE STEM CAP
(a) Remove the 16 valve stem caps from the cylinder head.
HINT:
Arrange the removed parts in the correct order.
6. REMOVE CYLINDER HEAD SUB-ASSEMBLY RH
(a) Uniformly loosen and remove the 2 bolts in the sequence
shown in the illustration.
(b) Using a 10 mm bi-hexagon wrench, uniformly loosen the 10
cylinder head bolts in the sequence shown in the illustration.
Remove the 10 cylinder head bolts and plate washers.
HINT:
Be sure to arrange the removed parts for each installation
position separately.
NOTICE:
Be careful not to drop washers into the cylinder head.
Head warpage or cracking could result from removing bolts in
an incorrect order.
3UR-FBE ENGINE MECHANICAL: CYLINDER HEAD GASKET (fo...
7. REMOVE CYLINDER HEAD GASKET RH
3UR-FBE ENGINE MECHANICAL: CYLINDER HEAD GASKET (fo...
Last Modified: 9-16-2014
6.6 A
Doc ID: RM000002S5304FX
Model Year: 2015
Model: Tundra
Prod Date Range: [08/2014 - ]
Title: 3UR-FBE ENGINE MECHANICAL: CYLINDER HEAD GASKET (for Bank 2): INSTALLATION; 2015 MY
Tundra [08/2014 - ]
INSTALLATION
1. INSPECT CYLINDER HEAD SET BOLT
2. INSPECT CYLINDER HEAD SUB-ASSEMBLY RH
3. INSTALL CYLINDER HEAD GASKET RH
(a) Check the piston protrusions for each cylinder.
(1) Clean the cylinder block with solvent.
(a) Place the cylinder head on the cylinder block.
NOTICE:
The cylinder head bolts are tightened in 3 progressive steps.
(1) Using a 10 mm bi-hexagon wrench, install and uniformly
tighten the 10 cylinder head bolts with the plate washers
in several steps, in the sequence shown in the illustration.
Torque:
36 N·m {367 kgf·cm, 27ft·lbf}
3UR-FBE ENGINE MECHANICAL: CYLINDER HEAD GASKET (fo...
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст