Toyota Tundra (2015 year). Manual — part 2930
(3) Using a moulding remover, detach the 2 clips and remove
the double-sided tape to remove the lower No. 1 side panel
moulding LH.
Text in Illustration
*1
Protective Tape
*2
Double-sided Tape
(c) for CrewMax:
(1) Using a heat light, heat the vehicle body and lower No. 1 side panel moulding LH.
(2) Put protective tape around the lower No. 1 side panel moulding LH.
(3) Using a moulding remover, detach the 2 clips and remove
the double-sided tape to remove the lower No. 1 side panel
moulding LH.
Text in Illustration
*1
Protective Tape
*2
Double-sided Tape
2. REMOVE REAR BODY NO. 3 PROTECTOR LH
HINT:
When removing the rear body No. 3 protector LH, heat the vehicle body and rear body No. 3 protector LH
using a heat light.
Standard:
ITEM
TEMPERATURE
Vehicle Body
40 to 60°C (104 to 140°F)
Rear Body No. 3 Protector LH
20 to 30°C (68 to 86°F)
NOTICE:
Do not heat the vehicle body or rear body No. 3 protector LH excessively.
(a) for Regular Cab:
(1) Using a heat light, heat the vehicle body and rear body No. 3 protector LH.
EXTERIOR: SIDE MOULDING: REMOVAL; 2015 MY Tundra [08/20...
(b) for Double Cab:
(1) Using a heat light, heat the vehicle body and rear body No. 3 protector LH.
(c) for CrewMax:
(1) Using a heat light, heat the vehicle body and rear body No. 3 protector LH.
EXTERIOR: SIDE MOULDING: REMOVAL; 2015 MY Tundra [08/20...
Last Modified: 9-16-2014
6.6 A
Doc ID: RM000002YRC009X
Model Year: 2015
Model: Tundra
Prod Date Range: [08/2014 - ]
Title: EXTERIOR: SIDE MOULDING: INSTALLATION; 2015 MY Tundra [08/2014 - ]
INSTALLATION
HINT:
Use the same procedure for the RH and LH sides.
The procedures listed below are for the LH side.
1. INSTALL REAR BODY NO. 3 PROTECTOR LH
HINT:
When installing the rear body No. 3 protector LH, heat the vehicle body and rear body No. 3 protector LH
using a heat light.
Standard:
ITEM
TEMPERATURE
Vehicle Body
40 to 60°C (104 to 140°F)
Rear Body No. 3 Protector LH
20 to 30°C (68 to 86°F)
NOTICE:
Do not heat the vehicle body or rear body No. 3 protector LH excessively.
(a) Clean the vehicle body surface.
(1) Using a heat light, heat the vehicle body surface.
(2) Remove the double-sided tape from the vehicle body.
(3) Wipe off any tape adhesive residue with cleaner.
(b) Installation temperature
(1) When the ambient temperature is below 15°C (59°F), perform the installation procedure after warming
HINT:
The most appropriate temperature for installing the tape is 25°C (77°F).
When the temperature is low, the tape turns stiff and falls off easily. When the temperature is high, the
tape loses elasticity.
(c) Before installation
(1) Make sure any dirt on and around the vehicle body surface where the tape will be installed (installation
poor appearance.
HINT:
Spray water on the shop floor to settle any dust.
(d) Key points for handling the tape
EXTERIOR: SIDE MOULDING: INSTALLATION; 2015 MY Tundra [...
NOTICE:
Do not bend the tape or leave it in a place with a high temperature.
NOTICE:
surface does not touch the vehicle body while applying the tape. Tilt the squeegee 40 to 50° (for
per second.
NOTICE:
HINT:
*1
Squeegee
*2
Rear Body No. 3 Protector LH
*3
Release Paper
*4
Application Tape
*a
Sectional View
*b
Non-padded Side
*c
Padded Side
*d
Pressing
*e
Pulling
-
-
EXTERIOR: SIDE MOULDING: INSTALLATION; 2015 MY Tundra [...
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст