Toyota FJ Cruiser (GSJ 10, 15 series). Instruction — part 205
ET–50
EXTERIOR – ROOF DRIP SIDE FINISH MOULDING
ET
7.
REMOVE ROOF DRIP SIDE FINISH MOULDING
RETAINER
HINT:
Use the same procedure to remove all the roof drip side
finish moulding retainers.
(a) Remove the screw and the roof drip side finish
moulding retainer.
8.
REMOVE FRONT DOOR OPENING TRIM
WEATHERSTRIP
HINT:
Use the same procedure as for the RH side (See Page
9.
REMOVE ASSIST GRIP PLUG
HINT:
Use the same procedure as for the RH side (See Page
10. REMOVE ASSIST GRIP ASSEMBLY
HINT:
Use the same procedure as for the RH side (See Page
11. REMOVE FRONT PILLAR GARNISH
HINT:
Use the same procedure as for the RH side (See Page
).
12. REMOVE FRONT PILLAR OUTER GARNISH
(a) Remove the nut.
(b) Disengage the 5 clips and remove the front pillar
outer garnish.
13. REMOVE ROOF SIDE GARNISH PROTECTOR
(a) Using a clip remover, remove the 4 clips.
(b) Remove the 3 pieces of double-sided adhesive tape
and the roof side garnish protector.
B135040
B135013
Double-sided Adhesive Tape
B135014E01
EXTERIOR – ROOF DRIP SIDE FINISH MOULDING
ET–51
ET
INSTALLATION
HINT:
The procedure described below is for the LH side. Use the
same procedure for both the RH and LH sides, unless
otherwise specified.
1.
INSTALL ROOF SIDE GARNISH PROTECTOR
(a) Install a new roof side garnish protector with the 4
clips.
2.
INSTALL FRONT PILLAR OUTER GARNISH
(a) Engage the 5 clips and install the front pillar outer
garnish.
(b) Tighten the nut.
Torque: 5.0 N*m (50 kgf*cm, 44 in.*lbf)
3.
INSTALL FRONT PILLAR GARNISH
HINT:
Use the same procedure as for the RH side (See Page
4.
INSTALL ASSIST GRIP ASSEMBLY
HINT:
Use the same procedure as for the RH side (See Page
).
5.
INSTALL ASSIST GRIP PLUG
HINT:
Use the same procedure as for the RH side (See Page
).
6.
INSTALL FRONT DOOR OPENING TRIM
WEATHERSTRIP
HINT:
Use the same procedure as for the RH side (See Page
).
Double-sided Adhesive Tape
B135014E01
B135013
ET–52
EXTERIOR – ROOF DRIP SIDE FINISH MOULDING
ET
7.
INSTALL ROOF DRIP SIDE FINISH MOULDING
RETAINER
HINT:
Use the same procedure to install all the roof drip side
finish moulding retainers.
(a) Install the roof drip side finish moulding retainer.
Torque: 5.0 N*m (50 kgf*cm, 44 in.*lbf)
8.
INSTALL WINDSHIELD OUTSIDE UPPER MOULDING
SUB-ASSEMBLY
(a) Clean the windshield glass.
(1) Using a scraper, remove the adhesive from the
windshield glass.
(2) Clean the outer circumference of the
windshield glass with a non-residue solvent.
NOTICE:
Do not touch the windshield glass surface
after cleaning it.
(b) Using a brush or sponge, apply Primer G to the
contact surface.
NOTICE:
•
Allow the primer to dry for 3 minutes or more.
•
Throw away any leftover Primer G.
•
Do not apply too much Primer G.
HINT:
If Primer G is applied to any areas other than those
specified, wipe off the primer with a clean shop rag
or piece of cloth before it dries.
(c) Apply adhesive.
Adhesive:
Toyota Genuine Windshield Glass Adhesive or
the equivalent
(1) Cut the tip off the cartridge nozzle.
HINT:
After cutting off the tip, use all adhesive within
the times indicated in the table below.
Usage time frame:
(2) Load the sealer gun with the cartridge.
B135040
Temperature
Usage Time Frame
35
°C (95°F)
15 minutes
20
°C (68°F)
1 hour 40 minutes
5
°C (41°F)
8 hours
EXTERIOR – ROOF DRIP SIDE FINISH MOULDING
ET–53
ET
(3) Apply adhesive to a new windshield outside
upper moulding, as shown in the illustration.
Specification:
(d) Engage the 6 claws and the 2 clips and install a new
windshield outside upper moulding.
NOTICE:
Do not drive the vehicle within the time
indicated in the table below.
Minimum time:
(e) Remove the protective tape.
A
A
A-A
a
b
c
B138634E01
Area
Measurement
a
7 mm (0.276 in.)
b
8 mm (0.315 in.)
c
10 mm (0.394 in.)
B135039
Temperature
Minimum time prior to driving
vehicle
35
°C (95°F)
1 hour 30 minutes
20
°C (68°F)
5 hour
5
°C (41°F)
24 hours
Protective Tape
B135038E01
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст