Toyota FJ Cruiser (GSJ 10, 15 series). Instruction — part 141
ED–60
ENGINE HOOD / DOOR – BACK WINDOW SUPPORT
ED
BODY
ENGINE HOOD / DOOR
BACK WINDOW SUPPORT
COMPONENTS
BACK DOOR TRIM
COVER
BACK WINDOW SUPPORT
CLIP
CLIP
B139384E01
ENGINE HOOD / DOOR – BACK WINDOW SUPPORT
ED–61
ED
REMOVAL
HINT:
•
Use the same procedure for both the RH and LH sides.
•
The procedure described below is for the LH side.
1.
REMOVE BACK DOOR TRIM COVER (See page
2.
REMOVE BACK WINDOW SUPPORT
(a) Using a screwdriver with its tip wrapped in
protective tape, remove the 2 stop rings and back
window support.
NOTICE:
•
Do not touch the rod of the back window
support with gloves, to avoid fibers from
adhering.
•
When foreign matter adheres to the rod, it
prevents the rod from moving smoothly and
reduces its holding power.
HINT:
Support the back door glass by hand while
removing the back window support.
INSTALLATION
1.
INSTALL BACK WINDOW SUPPORT
(a) Install the 2 stop rings onto the back window
support.
(b) Install the back window support.
2.
INSTALL BACK DOOR TRIM COVER (See page
B135523
B135551
ED–62
ENGINE HOOD / DOOR – BACK WINDOW SUPPORT
ED
DISPOSAL
HINT:
•
Use the same procedure for both the RH and LH sides.
•
The procedure described below is for the LH side.
1.
DISPOSE OF BACK WINDOW SUPPORT
(a) Horizontally fix the back window support in a vise
with the piston-rod pulled out.
(b) Wearing protective glasses, using a metal saw
gradually cut the shaded part between A and B,
shown in the illustration, to gradually release the
gas.
Specification
CAUTION:
•
Cover the area that is being cut with a shop
rag or a piece of cloth because there is a
possibility that metal shards may be
dispersed by the gas.
•
The gas is colorless, odorless and harmless.
A
B
a
b
B135552E01
Area
Measurement
a
80 mm (3.15 in.)
b
20 mm (0.80 in.)
1GR-FE ENGINE MECHANICAL – ENGINE
EM–1
EM
ENGINE
ON-VEHICLE INSPECTION
1.
INSPECT ENGINE COOLANT (See page
2.
INSPECT ENGINE OIL (See page
3.
INSPECT BATTERY (See page
4.
INSPECT AIR CLEANER FILTER ELEMENT SUB-
ASSEMBLY
5.
INSPECT SPARK PLUG (See page
6.
INSPECT FAN AND GENERATOR V BELT (See page
7.
INSPECT IGNITION TIMING
NOTICE:
•
Turn all the electrical systems OFF.
•
Conduct the inspection when the cooling fan
motor is turned OFF.
(a) Warm up the engine.
(b) When using the intelligent tester:
(1) Connect the intelligent tester to the DLC3.
(2) Select the following menu items: DIAGNOSIS /
ENHANCED OBD ll / DATA LIST / PRIMARY /
IGN ADVANCE.
(3) Inspect the ignition timing during idling.
Ignition timing:
7 to 24
°CA BTDC during idling
(Transmission in neutral position)
(4) Check that the ignition timing advances
immediately when the engine speed is
increased.
(c) When not using intelligent tester:
(1) Using SST, connect the terminals 13 (TC) and
4 (CG) of the DLC3.
SST
09843-18040
NOTICE:
Do not connect the terminals incorrectly as
it causes breakage of the engine.
(2) Remove the air cleaner.
Intelligent Tester
DLC3
CAN VIM
A129958E01
1 2 3 4 5 6
9 1011 1213141516
7 8
DLC3
TC
CG
A118802E01
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст