Toyota FJ Cruiser (GSJ 10, 15 series). Instruction — part 355
PM–42
PARK ASSIST / MONITORING – BACK SONAR SWITCH ASSEMBLY
PM
REMOVAL
1.
DISCONNECT CABLE FROM NEGATIVE BATTERY
TERMINAL
2.
REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY (for
Manual Transmission) (See page
)
3.
REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY (for
4WD) (See page
)
4.
REMOVE PARKING BRAKE HOLE COVER SUB-
ASSEMBLY (See page
)
5.
REMOVE FRONT CONSOLE BOX UPPER PANEL
SUB-ASSEMBLY (See page
)
6.
REMOVE FRONT CONSOLE BOX BOTTOM MAT (See
page
7.
REMOVE FRONT CONSOLE BOX (See page
)
8.
REMOVE INSTRUMENT LOWER COVER SUB-
ASSEMBLY (See page
9.
REMOVE BACK SONAR SWITCH ASSEMBLY
(a) Disengage the 2 claws and remove the back sonar
switch.
10. REMOVE BACK SONAR SWITCH BULB
(a) Remove the back sonar switch bulb.
11. REMOVE BACK SONAR SWITCH BULB CAP
(a) Remove the back sonar switch bulb cap.
B135185
B135186
B135187
PARK ASSIST / MONITORING – BACK SONAR SWITCH ASSEMBLY
PM–43
PM
INSPECTION
1.
INSPECT BACK SONAR SWITCH ASSEMBLY
(a) Check the resistance.
(1) Using an ohmmeter, measure the resistance
between the terminals.
Standard resistance
If the result is not as specified, replace the back
sonar switch.
(b) Check the operation.
(1) Apply battery voltage to the terminals and
check that the indicator illuminates.
Standard
If the result is not as specified, check the back
sonar switch bulb.
2.
INSPECT BACK SONAR SWITCH BULB
(a) Check the resistance.
(1) Using an ohmmeter, measure the resistance
between the terminals.
Standard resistance:
7 to 11
Ω at 20°C (68°F)
If the result is not as specified, replace the back
sonar switch bulb.
INSTALLATION
1.
INSTALL BACK SONAR SWITCH BULB CAP
(a) Install the back sonar switch bulb cap.
Ohmmeter
Battery
B135188E01
Tester Connection
Condition
Specified Condition
4 (ECU) - 6 (E)
OFF
Below 1
Ω
3 (IG) - 6 (E)
ON
Below 1
Ω
4 (ECU) - 6 (E)
Below 1
Ω
Condition
Standard
Positive battery - Terminal 1 (ILL+)
Negative battery - Terminal 2 (ILL-)
Illuminates
Ohmmeter
B138462E01
B135187
PM–44
PARK ASSIST / MONITORING – BACK SONAR SWITCH ASSEMBLY
PM
2.
INSTALL BACK SONAR SWITCH BULB
(a) Install the back sonar switch bulb.
3.
INSTALL BACK SONAR SWITCH ASSEMBLY
(a) Engage the 2 claws and install the back sonar
switch.
4.
INSTALL INSTRUMENT LOWER COVER SUB-
ASSEMBLY (See page
5.
INSTALL FRONT CONSOLE BOX (See page
6.
INSTALL FRONT CONSOLE BOX BOTTOM MAT (See
page
7.
INSTALL FRONT CONSOLE UPPER PANEL SUB-
ASSEMBLY (See page
8.
INSTALL PARKING BRAKE HOLE COVER SUB-
ASSEMBLY (See page
9.
INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY (for
4WD) (See page
10. INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY (for
Manual Transmission) (See page
)
11. CONNECT CABLE TO NEGATIVE BATTERY
TERMINAL
Torque: 3.9 N*m (40 kgf*cm, 35 in.*lbf)
B135186
B135185
PARKING BRAKE – PARKING BRAKE SYSTEM
PB–1
PB
PARKING BRAKE SYSTEM
PROBLEM SYMPTOMS TABLE
HINT:
Use the table below to help you find the cause of the problem.
The numbers indicate the ranked order of probability of each
of the possible causes. Check each part in the order
suggested. If necessary, replace these parts.
Symptom
Suspected area
See page
Brake drag
1. Parking brake lever travel (Out of adjustment)
2. Parking brake wire (Sticking)
3. Parking brake shoe clearance (Out of adjustment)
4. Parking brake shoe lining (Cracked or distorted)
5. Tension or return spring (Damaged)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст