Ford Focus RS (2011 year). Instruction — part 65
Removal Details
Item 2
Exterior front door handle retaining
screw
1. Loosen the exterior front door handle
retaining screw.
E40843
Installation Details
Item 2
Exterior front door handle retaining
screw
1. Tighten the exterior front door handle
retaining screw.
E40843
G296083en
501-14-
199
Handles, Locks, Latches and Entry Systems
501-14-
199
REMOVAL AND INSTALLATION
Door Latch Remote Control
1. Remove the door trim panel. For additional
information, refer to Section
501-05 [Interior
Trim and Ornamentation].
2. Remove the components in the order
indicated in the following illustration(s) and
table(s).
3
E40719
1
2
4
N
Description
Item
Door latch remote control handle lock
1
Door latch remote control cable
See Removal Detail
2
Description
Item
Door latch remote control retaining clip
3
Door latch remote control
See Removal Detail
4
3. To install, reverse the removal procedure.
Removal Details
Item 1
Door latch remote control handle lock
1. Operate the door latch remote control handle
lock to the lock position.
G296085en
501-14-
200
Handles, Locks, Latches and Entry Systems
501-14-
200
REMOVAL AND INSTALLATION
See Removal Detail
Item 2
Door latch remote control cable
1. Disconnect the door latch remote control
cable from the door latch remote control.
E40720
Item 4
Door latch remote control
1. Slide the door latch remote control away
from the door latch remote control retaining
clip.
G296085en
501-14-
201
Handles, Locks, Latches and Entry Systems
501-14-
201
REMOVAL AND INSTALLATION
Keyless Vehicle Module
General Equipment
Worldwide Diagnostic System (WDS)
Removal
All vehicles
1. Disconnect the battery ground cable.
For additional information,
refer to: Battery
Disconnect and Connect
(414-01 Battery,
Mounting and Cables, General Procedures).
Wagon
2. Open the loadspace storage compartment
lid.
E57936
4-door
3. Remove the loadspace floor covering.
4. Remove the rear lamp assembly access trim
panel.
• Remove the rear lamp assembly access trim
panel retaining clips.
E57937
5. Detach the loadspace trim panel to gain
access to the keyless vehicle module.
E57938
3-door and 5-door
6. Remove the loadspace floor covering.
7. Tilt the rear seat cushion forward.
8. Tilt the rear seat backrest forward.
9. Remove the C-pillar trim.
For additional information,
refer to: C-Pillar
Trim Panel - 4-Door/5-Door
(501-05 Interior
Trim and Ornamentation, Removal and
Installation).
10. Detach the liftgate opening weather strip.
E57939
11. Detach the parcel shelf support trim panel.
(3 door vehicle shown, 5 door vehicle
similar).
1. Remove the parcel shelf support trim panel
retaining screws.
2. Pull the parcel shelf support trim panel away
from the body panel to disengage the locking
clips between the D-pillar trim panel and the
parcel shelf support trim panel.
G458825en
501-14-
202
Handles, Locks, Latches and Entry Systems
501-14-
202
REMOVAL AND INSTALLATION
3. Feed the rear seat safety belt through the
parcel shelf support trim panel and position
the parcel shelf trim panel to one side.
E57940
1
1
2
3
All vehicles
12. Detach the keyless vehicle module. (3 door
vehicle shown, 5 door, 4 door and wagon
vehicles similar).
• Remove the keyless vehicle module retaining
screws.
E57952
13. Remove the keyless vehicle module.
• Disconnect the keyless vehicle module
electrical connectors.
E57953
Installation
All vehicles
1. To install, reverse the removal procedure.
2. If a new keyless vehicle module is installed,
program the new keyless vehicle module
using the WDS Program Module routine.
3. If a new keyless vehicle module is installed,
initialize the new keyless vehicle module to
the central junction box (CJB) and the
steering column lock control unit, using the
WDS Initialize System routine.
4. If a new keyless vehicle module is installed,
teach the minimum required number of keys
to the keyless vehicle module, using the
WDS Teach Key function.
Vehicles with global closing
5. Initialize the door window motors.
For additional information,
refer to: Door
Window Motor Initialization
(501-11 Glass,
Frames and Mechanisms, General
Procedures).
G458825en
501-14-
203
Handles, Locks, Latches and Entry Systems
501-14-
203
REMOVAL AND INSTALLATION
Keyless Vehicle Front Antenna
Removal
1.
Refer to: Floor Console - Vehicles Built From:
03/2007, Vehicles With: Center Armrest
(501-12 Instrument Panel and Console,
Removal and Installation).
2.
E119016
3.
E119017
Installation
1. To install, reverse the removal procedure.
G1224136en
501-14-
204
Handles, Locks, Latches and Entry Systems
501-14-
204
REMOVAL AND INSTALLATION
Keyless Vehicle Center Antenna
Removal
1.
Refer to: Floor Console - Vehicles Built From:
03/2007, Vehicles With: Center Armrest
(501-12 Instrument Panel and Console,
Removal and Installation).
2.
E119061
Installation
1. To install, reverse the removal procedure.
G1224138en
501-14-
205
Handles, Locks, Latches and Entry Systems
501-14-
205
REMOVAL AND INSTALLATION
Keyless Vehicle Rear Antenna
Removal
1.
E119076
2.
E101480
3.
E101481
4.
G1224140en
501-14-
206
Handles, Locks, Latches and Entry Systems
501-14-
206
REMOVAL AND INSTALLATION
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст