Ford Galaxy / Ford S-MAX. Manual — part 986
Is the resistance greater than 10,000 ohms?
Yes
GO to CC2
.
No
REPAIR circuits VDB06AB (GY/OG) and VDB07H
(VT/OG). REPEAT the self-test, CLEAR the DTCs.
REACTIVATE the system.
CC2: CHECK THE RCM COMMUNICATION BUS CIRCUIT FOR A SHORT CIRCUIT TO
GROUND
WARNING: To avoid accidental deployment, the RCM backup power supply must be
depleted. Wait at least one minute after disconnecting the battery ground cable(s) before
commencing any repair or adjustment to the SRS, or any component(s) adjacent to the
SRS sensors. Failure to follow these instructions may result in personal injury.
Measure the resistance between the RCM
C2R114-A pin 19, circuit VDB06AB (GY/OG),
harness side and ground.
1
Is the resistance greater than 10,000 ohms?
Yes
GO to CC3
.
No
REPAIR circuit VDB06AB (GY/OG). REPEAT the
self-test, CLEAR the DTCs. REACTIVATE the
system.
CC3: CHECK THE RCM COMMUNICATION BUS CIRCUIT FOR A SHORT CIRCUIT TO
BATTERY OR IGNITION
Ignition switch in position II.
1
Measure the voltage between the RCM C2R114-A
pin 20, circuit VDB07H (VT/OG), harness side
and ground.
2
Is any voltage present?
Yes
REPAIR circuit VDB07H (VT/OG). REPEAT the
self-test, CLEAR the DTCs. REACTIVATE the
system.
No
REPEAT the self-test, CLEAR the DTCs.
REACTIVATE the system.
PINPOINT TEST CD : DTC U3000 13: AIR BAG DIAGNOSTIC MONITOR
GROUND CIRCUIT OPEN
TEST CONDITIONS
DETAILS/RESULTS/ACTIONS
CD1: CHECK THE RCM GROUND CIRCUIT
WARNING: To avoid accidental deployment, the RCM backup power supply must be
depleted. Wait at least one minute after disconnecting the battery ground cable(s) before
commencing any repair or adjustment to the SRS, or any component(s) adjacent to the
SRS sensors. Failure to follow these instructions may result in personal injury.
NOTE: CHECK that the PAD switch is in the air bag live position before carrying out this
test.
Deactivate the SRS.
1
Check the RCM electrical connectors.
2
Are the RCM electrical connectors fully engaged?
Yes
Check the RCM installation.
REFER to:
Restraints Control Module (RCM)
(501-20B Supplemental
Restraint System, Removal and Installation).
REPEAT the self-test, CLEAR the DTCs. REACTIVATE the system. If the
DTC remains, INSTALL a new RCM.
REFER to:
Restraints Control Module (RCM)
(501-20B Supplemental
Restraint System, Removal and Installation).
No
CONNECT the RCM electrical connectors. REPEAT the self-test, CLEAR
the DTCs. REACTIVATE the system.
Supplemental Restraint System -
Clockspring Adjustment
S-MAX/Galaxy 2006.5 (02/2006-)
General Procedures
WARNINGS:
If there is a break between installing the clockspring and steering wheel rotation
sensor assembly and installing the steering wheel, the centralizing of the clockspring
must be repeated.
If the centralization of the clockspring is in doubt, the centralizing of the clockspring
must be repeated.
CAUTION: The clockspring and steering wheel rotation sensor assembly must not be
rotated in a couterclockwise direction more than the specified revolutions.
NOTE: Make sure that the road wheels are in the straight ahead position.
1.
1. Turn the clockspring rotor in a clockwise
direction until a resistance is felt.
2. Turn the clockspring in a counterclockwise
direction 2.5 revolutions.
2.
Check to see if the yellow roller is visible in
the clockspring window.
Using a suitable piece of tape, secure the
clockspring rotor to the clockspring body.
Supplemental Restraint System -
Deployed Air Bag Disposal
S-MAX/Galaxy 2006.5 (02/2006-)
General Procedures
WARNING: After deployment, the air bag module surface may contain deposits of
sodium hydroxide, a product of the gas generate combustion, that is irritating to the skin.
Use protective gloves when handling any deployed air bag module. Failure to follow this
instruction may result in personal injury.
1. Remove the deployed air bag module(s). For
additional information, refer to the relevant
procedure in this section.
2. Seal the deployed air bag module(s) in the
packaging from the new air bag module(s) or a
suitable polythene bag, and then dispose of in
accordance with local contaminated waste
regulations.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст