Ford Falcon. Manual — part 421
501-10-17 Seating 501-10-17
DIAGNOSIS AND TESTING (Continued)
PINPOINT TEST K : MIRROR DIP IS INOPERATIVE
Test Step
Result / Action to Take
K1
CHECK FOR IGNITION FUNCTION
Perform a seat recall and activate ignition before recall is complete.
Yes
Go to K3
Did the seat stop short of the recall position?
No
Go to K2
K2
CHECK FOR IGNITION AT THE SEAT CONNECTOR
Measure the harness voltage at CON-2 pin 2.
Yes
If DTC 15 is set problem is with the Harness
Is the Voltage >10V?
else replace seat module.
No
Refer to section 501-10.
K3
CHECK FOR REVERSE FUNCTION
With Ignition on and PRNDL in Reverse activate the Mirror Dip button,
Yes
hold the button for 2 seconds to ensure chime will happen even if the
Go to K5
function is currently enabled.
No
Did the seat chime?
Go to K4
K4
CHECK FOR REVERSE AT THE SEAT CONNECTOR
Measure the harness voltage at CON-2 pin 3.
Yes
If DTC 16 is set problem is with the Harness
Is the Voltage >10V?
else replace seat module.
No
Refer to PCM section 303-14.
K5
CHECK FOR MIRROR OPERATION
Program different mirror locations into the memory buttons and then
Yes
recall each memory position.
Replace Harness. Refer to removal and
installation instructions in this chapter.
Did the mirrors move to the correct location?
No
Refer to the Exterior Mirror section 501-09.
G73255 en
501-10-18 Seating 501-10-18
REMOVAL AND INSTALLATION
4. Unplug all electrical connectors from outboard
Front Seat Assembly
underside of seat.
Removal
1. Set seat back angle to vertical position and set
height adjustment to full up position.
2. Disconnect
the
battery.
WARNING: Wait at least one minute after
disconnecting the battery ground cable before
disconnecting any supplemental restraint
system electrical connector. Failure to follow
this warning could cause premature
deployment and may result in personal injury.
NOTE: Number of connectors depend on seat
option and may include seat belt pre-tensioner,
side airbag, memory and power connectors on
outboard side of seat (Refer to Section 501-20a).
3. Remove front and rear plastic track cover by
releasing metal spring.
5. Remove four seat mounting bolts.
6. Carefully remove the seat from the vehicle.
Installation
1. To install front seat, reverse the removal
procedure.
G73256 en
501-10-19 Seating 501-10-19
REMOVAL AND INSTALLATION (Continued)
Rear Seat Cushion
2. Press spring clip down to release.
Removal
1. To remove rear seat cushion push each side back
and up to release floor clips.
3. Pull bolster forward to remove, disengage plastic
hook at bottom.
Installation
1. Ensure that rear metal loop is engaged in sheet
metal as shown and push each side down to
engage floor clip.
Installation
1. To install, reverse the removal procedure.
Rear Seat Back
Removal
1. Remove seat bolster. Refer to Rear Seat Bolster
Rear Seat Bolster
in this section.
2. Delatch seat back and fold forward.
Removal
1. Insert screw driver down back of bolster.
G73259 en
501-10-20 Seating 501-10-20
REMOVAL AND INSTALLATION (Continued)
3. Place narrow screw driver between white cam
Installation
and bearing.
1. Ensure white cam is in disengaged position and
seat back is lying flat.
4. Disengage cam from bearing by levering
outboard.
2. Place cam in holder and raise seat back to
engage.
5. Lift seat back up vertically.
3. Check that cam has engaged properly.
6. Remove Rear Seat Back.
G73259 en
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст