Ford Falcon. Manual — part 422
501-10-21 Seating 501-10-21
DISASSEMBLY AND ASSEMBLY
Front Head Restraint
Back Cover
Disassembly and Assembly
Disassembly
1. Press locking button next to headrest guide and
1. Remove two screws located at bottom edge of
lift in direction shown.
back cover.
2. Slide cover down until hooks located at the top
Item
Description
are released.
1
Press locking button
2
Lift headrest
2. Detach trim cover retaining strip by removing the
2 retaining screws.
3. Carefully disengage side clips and lift the back
cover away.
3. Peel back the trim cover up and away to remove
from head restraint pad.
CAUTION: Failure to follow procedure
can result in damage to the side retention clip.
Assembly
1. Insert the top retaining/locating tabs and slide
cover upwards.
2. Locate and snap in the side clips.
G73261 en
501-10-22 Seating 501-10-22
DISASSEMBLY AND ASSEMBLY (Continued)
3. Replace the 2 lower edge screws.
Lumbar Knob
CAUTION: Failure to follow procedure
Disassembly and Assembly
can result in damage to the side retention clip.
1. Use a flat tool and remove lumbar knob cover.
Headrest Guides
Disassembly and Assembly
1. Remove headrest (Refer to Headrest in this
section).
2. Remove back cover (Refer to Back Cover in this
section).
3. Undo top J-clip retainer.
2. Remove
screw.
4. Insert your hand between the back rest foam pad
and the frame. With your fingers squeeze the
head rest guide ends and push upwards.
3. Place hands or fingers behind escutcheon/knob.
G73261 en
501-10-23 Seating 501-10-23
DISASSEMBLY AND ASSEMBLY (Continued)
4. Pull to remove knob and escutcheon together.
Recliner Knob and Outer Side Cover
Disassembly and Assembly
1. Remove 2 mounting screws from the outer side
cover.
CAUTION: Failure to do so may cause
cover to crack around cover mounting boss.
Inner Side Cover
Disassembly and Assembly
1. Undo screw from inner side cover.
2. Place hands behind side cover.
2. Remove inner side cover.
3. Pull side cover away from seat base to remove
the reclining knob and side cover together.
4. Where applicable, disconnect plugs from switch
and/or memory buttons.
G73265 en
501-10-24 Seating 501-10-24
DISASSEMBLY AND ASSEMBLY (Continued)
9. Unclip yellow plug from connector cradle (where
Front Seat Back
side air bag is fitted).
Disassembly and Assembly
1. Remove seat out of vehicle (Refer to Seats in this
section).
WARNING: Wait at least one minute after
disconnecting the battery ground cable before
disconnecting any supplemental restraint
system electrical connector. Failure to follow
this warning could cause premature
deployment and may result in personal injury.
2. Remove head rest (Refer to Headrest in this
section).
3. Remove plastic back cover (Refer to Back Cover
in this section).
10. Remove three fir tree clips (where side air bag is
4. Remove back cover (Refer to Back Cover in this
fitted).
section).
5. Remove lumbar knob (Refer to Lumbar Knob in
this section).
6. Remove recliner knob and outer side cover (Refer
to Recliner Knob and Outer Side Cover in this
section).
7. Remove inner side cover (Refer to Inner Side
Cover in this section).
8. Unclip connector cradle cover (where side air bag
is fitted).
WARNING: Never probe the connectors
on the air bag module. Doing so can result in
air bag deployment, which can result in
personal injury.
G73267 en
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст