Ford Falcon. Manual — part 414
501-09-3
Rear View Mirrors
501-09-3
DESCRIPTION AND OPERATION
Rear View Mirrors
The rear view mirrors consist of the following
components:
exterior rear view mirrors (standard electric
operation or memory operation)
exterior mirror control switch
door switch control module (memory mirrors only)
interior rear view mirror
integral ambient temperature sensor in LH
exterior mirror only
The exterior rear view mirrors are adjusted by the
exterior mirror control switch or via the memory
seat/mirror function buttons.
G90851 en
501-09-4
Rear View Mirrors
501-09-4
DIAGNOSIS AND TESTING
2. Visually inspect for obvious signs of mechanical
Rear View Mirrors
and electrical damage.
Refer to Wiring Diagram Section for schematic and
Visual Inspection Chart
connector information.
Mechanical
Electrical
Special Tool(s)
Exterior rear view
Central junction box
mirror(s)
(CJB) Fuse: RADIO
73III Automotive Meter
No.2 7.5A
105-R0057 or equivalent
Circuitry
Exterior rear view
mirror motor(s)
Exterior mirror control
switch
3. If an obvious cause for an observed or reported
concern is found, correct the cause (if possible)
Inspection and Verification
before proceeding to the next step.
1. Verify the customer concern by operating the
4. If the concern is not visually evident, determine
system, using appropriate standard mirror or
the symptom and proceed to the Fault Diagnosis
memory mirror flowchart.
Tables.
Symptom Chart
NOTE: Refer to fault diagnostic tables (Standard
mirror & Memory mirror).
Standard Mirror Fault Diagnostic Flow Chart
Switch vehicle electrics on via ignition.
Operate both LH & RH mirrors via door mirror control
switch.
1) Are both mirrors
No
Both mirrors non-functional. Check fuse for mirror
operational ?
system at fusebox GO to Step 2.
No
One mirror non-functional. Remove mirror & check for
+12V & GND at door connector using multimeter whilst
operating mirror switch (Refer to pinpoint tests A3 &
B1) Go to Step 6.
Yes
No system mulfunction
2) Is fuse intact ?
No
Replace fuse and retest. Go to Step 3.
Yes
Remove mirror switch and check for +12V and GND at
connector using multimeter. Refer pinpoint test A1 and
A2. Go to Step 4.
3) Is system functioning
No
Remove mirror switch and check for +12V and GND at
correctly ?
connector using multimeter. Refer pinpoint test A1 and
A2. Go to Step 4.
Yes
No system mulfunction
4) Is +12V and GND
No
Possible wiring malfunction. Check for continuity from
available at switch ?
fuse/GND to corresponding pins at switch connector
Repair discontinuous wiring. Recheck operation of
mirrors via switch. Go to Step 5.
Yes
Replace faulty switch. Recheck operation of mirrors via
switch. Go to Step 5.
5) Is system functioning
No
Replace door mirror and retest. Go to Step 7.
correctly ?
Yes
No system mulfunction
G90852 en
501-09-5
Rear View Mirrors
501-09-5
DIAGNOSIS AND TESTING (Continued)
6) Is +12V and GND
No
Replace mirror control switch and retest. Go to Step 7.
available at door/mirror
connector ?
Yes
Replace door mirror and retest. Go to Step 7.
7) Does new mirror or
Yes
No system mulfunction
switch function correctly ?
Memory Exterior Mirror Fault Diagnostic Flow Chart
NOTE: Various memory positions for seats and mirrors must be selected and stored in seat module prior to
commencement of checklist, as long as the system is (partially) operating.
Switch vehicle electrics on via ignition.
Operate both LH & RH mirrors via door mirror control
switch.
1) Are both mirrors
No
Both mirrors non-functional. Check fuses for mirrors
operational ?
and seat control module. Press seat/mirror memory
buttons and check for seat and mirror movement. GO
to Step 6.
No
One mirror only works. Press seat/mirror memory
buttons and check for seat and mirror movement. Go to
Step 3.
Yes
Both mirrors functional. Press seat/mirror buttons and
check for seat and mirror movement. Go to Step 2.
2) Do both mirrors and
No
Refer to Seat module diagnostics and replace module if
seats operate ?
necessary and retest.
Yes
No system mulfunction
3) Do both mirrors
No
Remove suspect mirror and check for +12V and ground
operate?
at door/mirror connector. (Refer pinpoint test D1 & D2).
Go to Step 4.
Yes
Possible faulty door switch module. Replace module
1R23 17E704 AA. Go to Step 8.
4) Is +12V and GND
No
Trace power and ground supply from door connector to
available at connector ?
source and repair.
Yes
Replace faulty mirror and retest. Go to Step 5.
5) Does replaced mirror
No
Refer to Seat module diagnostics and replace module if
function ?
necessary and retest.
Yes
No system mulfunction
6) Do seats and mirrors
No
Refer to Seat module diagnostics and replace module if
move ?
necessary and retest.
Yes
Possible faulty door mirror switch. Replace switch. Go
to Step 7.
7) Do mirrors operate with
No
Possible faulty door switch module. Replace module
new switch ?
1R23 17E704 AA. Go to Step 8.
Yes
No system mulfunction
8) Do mirrors work with
No
Refer to Seat module diagnostics and replace module if
new module ?
necessary and retest.
Yes
No system mulfunction
G90852 en
501-09-6
Rear View Mirrors
501-09-6
DIAGNOSIS AND TESTING (Continued)
Connector Circuit Reference
C86
Pin Number(s)
Circuit Designation/Description
Normal Condition/Measurement
1
Circuit 540A (R)
0 voltage, less than 5 ohms between power
mirror switch and right front mirror motor
2
Circuit 541B (L)
0 voltage, less than 5 ohms between power
Mirror x direction control
mirror switch and right front mirror motor
3
Circuit 544A (V)
0 voltage, less than 5 ohms between power
Mirror y direction control
mirror switch and right front mirror motor
C88
Pin Number(s)
Circuit Designation/Description
Normal Condition/Measurement
1
Circuit 299 (V-R)
0 voltage, less than 5 ohms between the power
Power mirror switch power input
mirror switch and ignition switch
2
Circuit 57F (B)
0 voltage, less than 5 ohms between and
Power mirror switch ground
chassis ground
3
Circuit 540B (R)
0 voltage, less than 5 ohms between power
mirror switch and front mirror motors
4
Circuit 541A (L)
0 voltage, less than 5 ohms between power
Right mirror x direction control
mirror switch and right front mirror motors
5
Circuit 541B (L)
0 voltage, less than 5 ohms between power
Left mirror x direction control
mirror switch and left front mirror motors
6
Circuit 544A (V)
0 voltage, less than 5 ohms between power
Right mirror y direction control
mirror switch and right front mirror motors
7
Circuit 544B (V)
0 voltage, less than 5 ohms between power
Left mirror y direction control
mirror switch and left front mirror motors
G90852 en
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст