Ford Falcon. Manual — part 412
501-08-4
Exterior Trim and Ornamentation
501-08-4
REMOVAL AND INSTALLATION (Continued)
Rear Decklid Moulding — High Series, Rear Decklid Moulding — Low Series,
SWB Sedan
SWB Sedan
Removal
Removal
1. Remove 6 off nuts from inside decklid.
1. Remove 4 off nuts from inside decklid.
Item
Description
Item
Description
1
Nut - M5
1
Nut - M5
2
Ornament Assy Lugg Comp Door
2. Carefully release the two lower inboard retainers
from within the decklid using a screwdriver to
2. Carefully remove the moulding.
depress the locking tabs and remove the
3. Pull out wiring grommet and unplug wiring
moulding.
connector for license plate lamps.
3. Pull out the wiring grommet and unplug the wiring
Installation
connector for license plate lamps.
1. Feed in license plate lamp wire into decklid and
Installation
insert lamp wire grommet.
1. Feed in license plate lamp wire into decklid and
2. Plug in connector.
insert lamp wire grommet.
3. Line up 4 off studs with decklid and insert (Insure
2. Plug in connector.
seals are fitted to appliqué).
3. Line up top 4 off studs with decklid and rotate
4. Insert screws and torque.
moulding so as to insert lower two outboard studs
and two inboard retainers, and press home
(Insure seals are fitted to moulding including
retainers).
4. Insert screws and torque.
G86722 en
501-08-5
Exterior Trim and Ornamentation
501-08-5
REMOVAL AND INSTALLATION (Continued)
Window Moulding
Rear Liftgate Moulding — Wagon
Removal
Removal
1. Remove the liftgate interior trim.
2. Remove the four mounting screws.
Item
Description
1
Moulding - Liftgate
2
Nut - M5x0.8
3. Unplug the wiring connector.
Installation
1. To install, reverse the removal procedure.
Rear Decklid Moulding — Wagon
Removal
1. Remove 6 off nuts from inside decklid.
2. Carefully remove the moulding.
Installation
1. Line up 6 off studs with decklid and insert (Insure
seals are fitted to moulding).
2. Insert screws and torque.
G86727 en
501-08-6
Exterior Trim and Ornamentation
501-08-6
REMOVAL AND INSTALLATION (Continued)
Door Moulding — All Vehicles
Removal
1. Remove the applique moulding by pulling the clip.
Sedan
Item
Description
1
Rivet
2
Moulding
3
Clip
2. Use an adhesive cleaner to remove all tape
Item
Description
residue on the vehicle.
1
Applique
Installation
2
Wheatherstrip
1. Remove the backing tape from the applique.
3
Foam Tape
Ute
Item
Description
1
Applique - B Pillar Rear Door
2
Applique - B Pillar Front Door
Item
Description
3
Rivet
1
Wheatherstrip
2
Door Inner
2. Insert the applique into position and clip it at the
top.
3
Applique
3. Push the applique forward onto the door frame.
4
Rivet
4. Press firmly on the surface of the applique to
ensure tape contact over the full length.
G86727 en
501-08-7
Exterior Trim and Ornamentation
501-08-7
REMOVAL AND INSTALLATION (Continued)
4. Remove all rocker moulding seal clips from the
Rocker Panel Moulding — SWB & LWB
top slots.
Removal
1. Remove the three clips along the underside of the
rocker panel moulding.
5. Remove rocker panel moulding.
Installation
1. Locate rocker moulding lower fixing channel onto
rocker panel weld seam.
Item
Description
2. Roll rocker panel in vertical position to locate
1
Location of Metal Clip
rocker seal clips into corresponding top slots.
2
Rocker Moulding
3. Fully insert all rocker moulding clips starting from
2. Dislodge the metal clip.
the first front clip.
4. Ensure all clips are fully located home.
5. Fully insert the three fir tree clips on the
underside, to the floor in corresponding holes.
6. Insert 2 front splash shield to rocker scrivets.
Body Side Protection Moulding
Removal
NOTE: The procedures below covers the removal and
Installation of the double sided tape as used on
Falcon BSPMs and other Falcon applications.
1. Carefully cut the end of the tape on the BSPM
vertically to split the foam.
2. Peel the BSPM off the door, taking care not to
3. Remove the 2 scrivets attaching front splash
damage it if the BSPM is to be reused (not
shield to the rocker.
recommended).
3. Use an adhesive cleaner to remove tape residue
on the vehicle. Saturate the remaining tape and
use a squeegee to remove. All the adhesive
residue must be cleaned off the vehicle.
4. Give the vehicle a final wipe with a 70% isopropyl
alcohol and water mixture (rubbing alcohol).
5. Dry with a clean cloth.
Installation
1. Wipe metal surface with clean rag and isopropyl
alcohol solution (50/50 min. solution).
NOTE: Ensure ambient temperature is at a
minimum of 16 deg Celsius and is dry.
2. Remove the backing tape without contaminating
the adhesive surface.
G86731 en
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст