Ford Falcon. Manual — part 359
415-00-15
Entertainment System — General Information
415-00-15
DIAGNOSIS AND TESTING (Continued)
Test Step
Result/Action to Take
Acronyms
F10
Check that the wiring connections between the ICC Yes
and amplifier.
Go to F11.
Are connections correct?
No
Repair/replace wiring as
per wiring procedure
Replace fuse if blown and
retest.
F11
Replace the subwoofer amplifier.Replace the fuse if Yes
blown.
Original amplifier is faulty.
Is the subwoofer speaker working correctly?
Retest with a new
amplifier.
No
Refit the original amplifier
and continue.
F12
Replace the subwoofer speaker.
Yes
Replace the fuse if blown.
Original subwoofer is
Is the subwoofer speaker working correctly?
faulty. Retest with a new
subwoofer.
No
Replace the ICC. Refit the
original subwoofer
speaker. Replace fuse if
blown and retest.
TEST G : SPEAKER FAULT
Using the WDS data logger function activate the following acronyms.
RUN_POS, ACC_POS, POWER_SW
Test Step
Result/Action to Take
Acronyms
G1
Turn the ignition on.
Yes
RUN_POS
Check pid’s using data logger.
Go to G2.
No
Repair faulty ignition
system and retest.
G2
Check that the accessories are on.
Yes
ACC_POS
Check pid’s using data logger.
Go to G3.
Are the accessories on?
No
Repair faulty ignition
system and retest.
G3
Check to see if the ICC audio is turned on.
Yes
Is the audio on?
Go to G5.
No
Go to G4.
G68759 en
415-00-16
Entertainment System — General Information
415-00-16
DIAGNOSIS AND TESTING (Continued)
Test Step
Result/Action to Take
Acronyms
G4
Push the ICC audio power button.
Yes
Check pid’s using data logger.
Go to G5.
Does the ICC audio turn on?
No
Go to ICC does not turn
on symptom in the
symptom chart.
G5
Cycle the ICC balance and fade controls.
Yes
Inspect the ICC balance and fade displays.
Go to G6.
Do the balance and fade displays operate?
No
Replace ICC and retest.
G6
Cycle the ICC balance and fade controls.
Yes
Check for correct operation of all speakers.
No fault.
Do all speakers operate correctly?
No
Continue.
G7
Check vehicle speaker wiring for short to power or
Yes
ground.
Go to G8.
Is wiring OK?
No
Repair/replace wiring as
per wiring procedure
G8
Substitute any faulty speakers with a new speaker.
Yes
Do all speakers operate correctly?
Original speaker is
faulty.Fit new speaker and
retest.
No
Continue.
G9
Remove the ICC.
Yes
Check for continuity of vehicle speaker wires
Replace ICC and retest.
between the ICC instrument panel connector and
No
any faulty speaker.
Repair/replace wiring as
Refer to wiring diagram.
per wiring procedure
Are connections correct?
TEST H : POOR RADIO RECEPTION
Using the WDS data logger function activate the following acronyms.
RUN_POS, ACC_POS, POWER_SW, ATNN_RSS
Test Step
Result/Action to Take
Acronyms
H1
Turn the ignition on.
Yes
RUN_POS
Check pid’s using data logger.
Go to H2
Are the accessories on?
No
Repair faulty ignition
system and retest.
G68759 en
415-00-17
Entertainment System — General Information
415-00-17
DIAGNOSIS AND TESTING (Continued)
Test Step
Result/Action to Take
Acronyms
H2
Check to see if the ICC audio is turned on.
Yes
POWER_SW
Is the audio on?
Go to H4.
No
Go to ICC does not turn
on symptom in the
symptom chart.
H3
Push the ICC audio power button.
Yes
POWER_SW
Check pid’s using data logger.
Go to H4.
Does the ICC audio turn on?
No
Go to ICC does not turn
on symptom in the
symptom chart.
H4
Turn on the heater backlight.
ATNN_RSS
Yes
Check for poor AM and FM radio reception.
Go to H5.
Check pid’s using data logger.
No
Is the radio reception poor?
Go to H6
NOTE: Tinting of the rear window may affect radio
reception.
H5
Check that the rear window FM Antenna and the
Yes
AM antenna are not damaged.
Go to H6
Are the antennas OK?
No
Replace / rectify faulty
antenna.
H6
Check reception with engine running.
Yes
RUN_POS,
Start the vehicles engine.
Go to H7
ATNN_RSS
Check pid’s using data logger.
No
Is the radio reception poor?
Correct operation.
H7
Check / repair the vehicles suppressor and the
Yes
ATNN_RSS
antenna module ground connection.
Go to H8.
Check pid’s using data logger.
No
Is the radio reception poor?
Fault rectified. Retest
ICC.
H8
Check that the on glass antenna module has power Yes
connected.
Go to H12.
Is there power to the module?
No
Continue.
H9
Check the antenna fuse.
Yes
Is the fuse blown?
Go to H10.
No
Go to H12.
H10
Remove the faulty fuse and replace with a new fuse Yes
of correct rating.
Go to H11.
Does the fuse blow?
No
Retest.
G68759 en
415-00-18
Entertainment System — General Information
415-00-18
DIAGNOSIS AND TESTING (Continued)
Test Step
Result/Action to Take
Acronyms
H11
Check for a short in the antenna module wiring.
Yes
Is the wiring OK?
Replace the antenna
module and retest.Ensure
that the faulty fuse is
replaced.
No
Repair/replace wiring as
per wiring
procedureEnsure that the
faulty fuse is replaced.
H12
Check the antenna module by substituting with
Yes
ATNN_RSS
another module.
Install original antenna
Check pid’s using data logger.
module and Go to H13.
Is the radio reception poor?
No
Original antenna module
is faulty.
H13
Check antenna rear coaxial cable and connection
Yes
at left hand cowl side.
Go to H14.
Is cable / connection OK.
No
Rectify faulty cable /
connection and retest.
H14
Remove the ICC.
Yes
Check that the coaxial cable and connections to the Replace ICC and retest.
ICC are OK.
No
Is cable / connection OK?
Rectify faulty cable /
connection and retest.
TEST I : AUDIO STEERING WHEEL SWITCH NOT FUNCTIONING
Using the WDS data logger function activate the following acronyms.
RUN_POS, ACC_POS, POWER_SW, VOL_UP, VOL_DN, SEEK_BTN, MODE_SW
Test Step
Result/Action to Take
Acronyms
I1
Turn the ignition on.
Yes
RUN_POS
Check pid’s using data logger.
Go to I2.
Is the ignition on?
No
Repair faulty ignition
system and retest.
I2
Check that the accessories are on.
Yes
ACC_POS
Check pid’s using data logger.
Go to I3.
Are the accessories on?
No
Repair faulty ignition
system and retest.
I3
Check to see if the ICC audio is turned on.
Yes
Is the audio on?
Go to I5.
No
Go to I4.
G68759 en
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст