Ford Falcon. Manual — part 358
415-00-11
Entertainment System — General Information
415-00-11
DIAGNOSIS AND TESTING (Continued)
Test Step
Result/Action to Take
Acronyms
C13
Eject all CD’s from the ICC.
Yes
CDSLOT1,
Check pid’s using data logger.
No fault. ICC functioning
CDSLOT2,
Did all CD’s eject?
correctly.
CDSLOT3,
No
CDSLOT4,
Replace ICC and retest.
CDSLOT5,
CDSLOT6
TEST D : CD FOCUS ERROR
Using the WDS data logger function activate the following acronyms.
RUN_POS, ACC_POS, POWER_SW, CDSLOT1
Test Step
Result/Action to Take
Acronyms
D1
Turn the ignition on.
Yes
RUN_POS
Check pid’s using data logger.
Go to D2
Is the ignition on?
No
Repair faulty ignition
system and retest.
D2
Check that the accessories are on.
Yes
ACC_POS
Check pid’s using data logger.
Go to D3
Are the accessories on?
No
Repair faulty ignition
system and retest.
D3
Check to see if the ICC audio is turned on.
Yes
Check pid’s using data logger.
Go to D5
Is the audio on?
No
Go to D4
D4
Push the ICC audio power button.
Yes
POWER_SW
Check pid’s using data logger.
Go to D5
Does the ICC audio turn on?
No
Go to ICC does not turn
on symptom in the
symptom chart.
D5
Insert a known good original genuine CD.
Yes
CDSLOT_1
Ensure that the CD is inserted with the label facing
Go to D6
up.
No
Check pid’s using data logger.
Replace the ICC and
Is the CD inserted?
retest.
D6
Check that the CD plays correctly.
Yes
Does the CD play correctly?
ICC functioning correctly.
No
Continue
G68759 en
415-00-12
Entertainment System — General Information
415-00-12
DIAGNOSIS AND TESTING (Continued)
Test Step
Result/Action to Take
Acronyms
D7
Insert the ICC head cleaning CD and operate as
Yes
CDSLOT_1
per procedures.
Go to D8
Remove the head cleaning CD.
No
Insert a known good original genuine CD.
Replace the ICC and
Ensure that the CD is inserted with the label facing
retest.
up.
Check pid’s using data logger.
Is the CD inserted?
D8
Check that the CD plays correctly.
Yes
Does the CD play correctly?
ICC functioning correctly.
No
Replace ICC and retest.
TEST E : ICC DOES NOT OPERATE
Using the WDS data logger function activate the following acronyms.
RUN_POS, ACC_POS, POWER_SW
Test Step
Result/Action to Take
Acronyms
E1
Turn the ignition on.
Yes
RUN_POS
Check pid’s using data logger.
Go to E2
Is the ignition on?
No
Repair faulty ignition
system and retest.
E2
Check that the accessories are on.
Yes
Check pid’s using data logger.
Go to E3
Are the accessories on?
No
Repair faulty ignition
system and retest.
E3
Check to see if the ICC audio is turned on.
Yes
Check pid’s using data logger.
Go to E5
Is the audio on?
No
Go to E4
E4
Push the ICC audio power button.
Yes
POWER_SW
Check pid’s using data logger.
No fault. ICC functioning
Does the ICC audio turn on?
correctly.
No
Continue.
E5
Check to see if the ICC fuse is blown.
Yes
Is the fuse blown?
Go to E6
No
Go to E8
E6
Replace the blown ICC fuse with a new fuse of
Yes
correct value.
Go to E7
Does the fuse blow again?
No
Retest ICC
G68759 en
415-00-13
Entertainment System — General Information
415-00-13
DIAGNOSIS AND TESTING (Continued)
Test Step
Result/Action to Take
Acronyms
E7
Remove the ICC.
Yes
Replace the blown ICC fuse with a new fuse of
Repair/replace wiring as
correct value.
per wiring procedure
Does the fuse blow again?
Install the ICC and
replace blown fuse.
Retest ICC.
No
ICC is faulty. Replace with
a new ICC and retest.
E8
Check that the battery voltage is greater than 10.5
Yes
Volts with the ignition on.
Go to E9
Is the battery voltage greater than 10.5Volts?
No
Rectify vehicles power
supply and retest.
E9
Remove the ICC.
Yes
Inspect both halves of the ICC self-aligning
Go to E10
connector.
No
Is the self-aligning connector damaged?
Go to E12
E10
Inspect both halves of the ICC self-aligning
Yes
connector.
Replace the ICC.Replace
Are both halves of the connector damaged?
the instrument panel self-
aligning connector.
No
Continue.
E11
Inspect the self- aligning connector on the
Yes
Instrument panel.
Replace the instrument
Is this half of the connector faulty?
panel self- aligning
connector.Re-fit ICC and
retest.
No
Replace ICC and retest.
E12
Check for a ICC supply voltage of 10.5
Yes
Volts minimum at the ICC instrument panel
Replace ICC and retest.
self-aligning connector.
No
Refer to vehicle wiring diagram.
Repair wiring to the ICC
instrument panel
connector and retest.
TEST F : SUBWOOFER FAULT
Using the WDS data logger function activate the following acronyms.
RUN_POS, ACC_POS, POWER_SW
Test Step
Result/Action to Take
Acronyms
F1
Turn the ignition on.
Yes
RUN_POS
Check pid’s using data logger.
Go to F2
Is the ignition on?
No
Repair faulty ignition
system and retest.
G68759 en
415-00-14
Entertainment System — General Information
415-00-14
DIAGNOSIS AND TESTING (Continued)
Test Step
Result/Action to Take
Acronyms
F2
Check that the accessories are on.
Yes
ACC_POS
Check pid’s using data logger.
Go to F3
Are the accessories on?
No
Repair faulty ignition
system and retest.
F3
Check to see if the ICC audio is turned on.
Yes
Is the audio on?
Go to F5
No
Go to F4
F4
Push the ICC audio power button.
Yes
Check pid’s using data logger.
Go to F5
Does the ICC audio turn on?
No
Go to ICC does not turn
on symptom in the
symptom chart.
F5
Tune to a known radio station.
Yes
Is the subwoofer speaker working correctly?
No Fault.
No
Continue.
F6
Check the subwoofer amplifier fuse.
Yes
Is the fuse OK?
Go to F8.
No
Continue.
F7
Remove the faulty fuse and replace with a new fuse Yes
of correct value.
Go to F8.
Does the fuse blow again?
No
Retest for correct
operation.
F8
Check the amplifier power and ground connections. Yes
Are connections correct?
Go to F9
No
Repair/replace wiring as
per wiring
procedureReplace fuse if
blown and retest.
F9
Check connections between the amplifier and
Yes
subwoofer speaker.
Go to F10.
Are connections correct?
No
Repair/replace wiring as
per wiring
procedureReplace fuse if
blown and retest.
G68759 en
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст